锻压技术

模锻压机完全混合同步系统的建模与分析

英文标题：Modeling and analysis of completely hybrid synchronous system for forging press

作者：罗国平李毅波潘晴

单位：中南大学

分类号：

出版年,卷(期):页码：2015,40(7):92-97

摘要：

同步控制系统是保证模锻压机正常工作和系统性能的关键部分。介绍了一种基于主动纠偏和被动纠偏的完全混合同步系统，利用拉普拉斯变换法，通过分析该系统建立了多变量数学模型。针对多变量特点，对其进行了控制变量优化。并在系统优化基础上，利用MATLAB软件进行仿真。仿真结果显示，横梁偏转0.015 s时出现最大偏转角为1.4×10-4 rad，0.5 s完成纠偏达到水平状态。实验结果表明，该优化系统模型可行，能够快速响应且纠偏效果良好。

Synchronous control system is a key part to ensure the normal operation of forging press and good system performance. A completely hybrid synchronous system based on active rectification and passive rectification was introduced, and a multi-variable mathematical model was built by analyzing the system with Laplace transform method. For multi-variable characteristics, control variables of the system were optimized. And simulation was carried out by MATLAB based on system optimization. The simulation shows that when the beam deflects, the maximum deflection angle of 1.4×10-4 rad appears at 0.015 s, and the moving beam rectification is accomplished by recovering back to horizontal plane at 0.5 s. The result shows that the optimization system model is feasible with fast response performance and good rectification performance.

基金项目：

国家重点基础研究发展计划（“973”计划）资助项目（2011CB706802）

罗国平（1989-），男，硕士研究生

参考文献：

[1]俞新陆. 液压机的设计与应用[M]. 北京:机械工业出版社, 2006.

Yu X L. Design and Application of Hydraulic Press[M]. Beijing: China Machine Press, 2006.

[2]谭建平,刘昊. 溢流补偿型液压位置保持系统的研究及应用[J]. 机械工程学报, 2004, 40(3): 119-123.

Tan J P, Liu H. Research and application of the oil leak-off compensating in the hydraulic position-holding system[J]. Chinese Journal of Mechanical Engineering,2004, 40(3): 119-123.

[3]汤迎红,刘忠伟,青先麒 . 巨型模锻液压机同步系统性能影响因素的分析[J]. 锻压技术, 2014, 39(4): 77-83 .

Tang Y H, Liu Z W, Qing X Q. Analysis of the factors affecting the performance of the synchronization system for giant forging hydraulic presses [J]. Forging & Stamping Technology, 2014, 39(4): 77-83 .

[4]段俊. 巨型液压机被动同步平衡控制系统的控制策略与实验研究[D]. 长沙:中南大学, 2010.

Duan J. Research on Control Strategy and Experiment of Passive Synchronization of Balance Control System for Giant Hydraulic Press[D]. Changsha: Central South University, 2010.

[5]蒲亨林. 800 MN模锻压机被动同步系统研究[D]. 重庆:重庆大学, 2012.

Pu H L. Research on Passive Synchronous Balancing System of 800 MN Forging Hydraulic Press[D]. Chongqing: Chongqing University, 2012.

[6]倪敬, 项占琴, 潘晓弘，等. 多缸同步提升电液系统建模和控制[J]. 机械工程学报, 2006, 42(11): 81-87.

Ni J, Xiang Z Q,Pan X H, et al. Motion synchronization modeling and control for multi-cylinder electro-hydraulic elevating system[J]. Chinese Journal of Mechanical Engineering,2006, 42(11): 81-87.

[7]刘新良. 巨型模锻液压机主动同步控制系统研究[D]. 长沙:中南大学, 2010.

Liu X L. Research of Active Synchronous Control System for Giant Forging Hydraulic Press[D].Changsha: Central South University, 2010.

[8]于革刚, 吴定安, 吴进军，等. 大型模锻压机同步控制技术研究[J]. 锻压技术, 2011, 36(3): 63-66.

Yu G G, Wu D A,Wu J J,et al. Research on synchronous control technology for large forging press[J]. Forging & Stamping Technology, 2011, 36(3):63-66

[9]潘晴, 黄明辉, 李毅波，等. 多缸并行驱动液压系统建模与动态特性分析[J]. 四川大学学报:工程科学版, 2014, 46(1): 193-196.

Pan Q, Huang M H, Li Y B,et al. Modeling and analysis of dynamic characteristics for multi-cylinder hydraulic parallel drive system[J]. Journal of Sichuan University:Engineering Science Edition, 2014, 46(1): 193-196.

[10]王春行. 液压控制系统[M]. 北京:机械工业出版社, 2010.

Wang C X. Hydraulic Control Systems[M].Beijing: China Machine Press, 2010.

[11]Hong S, Chiug T C. Motion synchronization for multi-cylinder electro-hydraulic systems[J]. IEEE/ASME Transactions on Mechatronics, 2002, 7(2): 171-181.

服务与反馈：

【文章下载】【加入收藏】