锻压技术

等通道角挤压对高纯铝力学性能的影响

英文标题：Influence of equal channel angular extrusion on mechanical property of high purity aluminum

作者：高松松王进

单位：青岛理工大学

分类号：TG376

出版年,卷(期):页码：2015,40(8):132-134

摘要：

对高纯铝分别进行了Bc路径和C路径的等通道角挤压，采用显微维氏硬度计测试硬度，研究结果表明，经过4道次挤压后，Bc路径试样硬度达到59.8 HV，C路径试样硬度达到54.56 HV。并分析了ECAP实验对材料拉伸性能的影响。经过8道次挤压后，高纯铝的抗拉强度提高了100%，在第3道次达到最大值，为108 MPa。伸长率在第1道次后剧烈下降,由44%下降至18.3%，随后又略有上升。进行了热稳定性实验，分别将试样加热到100和200 ℃，保温1 h。结果表明，退火后高纯铝的硬度和抗拉强度都有所下降，不同的退火温度对硬度的影响几乎相同，而对抗拉强度的影响差别较大。

The high purity aluminum was extruded through routes Bc and C by equal channel angular extrusion(ECAE), and their micro-hardness values were measured by a leitzs micro-hardness tester. The results show that the hardness values can reach 59.8 HV and 54.56 HV by routes Bc and routes C respectively via four pass extrusion, and the influences of ECAE tests on tensile properties are studied. The tensile strength improves by 100% after eight pass extrusion. At the third pass, the tensile strength reaches the maximum of 108 MPa. Elongation drops from 44% to 18.3% dramatically after the first pass, and then increases slightly. The thermal stability tests were conducted by heating samples of 100 ℃ and 200 ℃ with preserving for 1 hour respectively. The results show that the hardness and the tensile strength of the high purity aluminum after annealing decrease, and the influence of different annealing temperatures on the hardness is almost the same, but that on the tensile strength is different.

基金项目：

国家自然科学基金资助项目（51205217）

高松松（1991-），女，硕士研究生王进(1978-),男，博士，副教授

参考文献：

［1］Valiev R Z, Islamgaliev R K, Alexandrov I V. Bulk nanostructured materials from severe plastic deformation[J].Progress in Materials Science,2000, 45:103-189.
［2］Lowe T C,Valiev R Z.Producing nanoscale microstructures through severe plastic deformation[J]. JOM,2000,52(4):27-28.
［3］陈嘉会，刘新材，潘晶.等通道转角挤压组织演变规律的研究进展[J].稀有金属，2014,38（5）：905-914.Chen J H,Liu X C,Pan J. Progress in microstructural evolution of equal-channel angular pressing process[J]. Chinese Journal of Rare Metals,2014,38(5):905-914.
［4］亓博丽，赵西成，杨西荣，等. 工业纯钛室温多道次 ECAP 变形后横截面的硬度均匀性分析[J].稀有金属，2014,38（1）:15-21.Qi B L,Zhao X C,Yang X R,et al. Evolution of hardness homogeneity on transverse section of commercially pure titanium processed by ECAP at room temperature[J]. Chinese Journal of Rare Metals,2014,38(1):15-21.
［5］周超，彭必友，沈冰，等.基于变形均匀性的AZ31镁合金ECAP多道次成形工艺研究[J].锻压技术，2013,38(3):145-151.Zhou C,Peng B Y,Shen B,et al. Study of forming process for AZ31 magnesium alloy during multiple passes ECAP baesd on homogeneous deformation[J]. Forging & Stamping Technology,2013,38(5):145-151.
［6］王金锋，白朴存，张秀云，等.ECAP对纯铝拉伸性能和断裂行为影响的研究[J].航空材料学报，2009，29（3）：33-38.Wang J F, Bai P C, Zhang X Y, et al.Investigation of effect of tensile property and fracture behavior of pure aluminum during ECAP[J].Journal of Aeronaut Ical Materials,2009,29(3):33-38.
［7］郭晓琴，黄靖.等通道挤压镁合金的微观组织与硬度[J].热加工工艺，2013,42(11):118-120.Guo X Q, Huang J. Microsture and hardness of magnesium alloy by ECAP[J].Hot Working Technology,2013,42(11):118-120.
［8］王大勇，顾小龙.靶材制备研究现状及研发趋势[J].浙江冶金，2007,(4):1-3.Wang D Y, Gu X L.Preparation process research status and development trend of target[J].Journal of Zhejiang Metallurgy,2007,(4):1-3.
［9］GB/T 228.1—2010，金属材料拉伸试验第1部分:室温试验方法[S]. GB/T 228.1—2010，Metallic materials - Tensile testing - Part 1 : Method of test at room temperature [S].
［10］蒋树农，刘楚明，李慧中，等.高纯多晶铝的动态再结晶[J].中南大学学报：自然科学版，2004,35(6):935-940.Jiang S N, Liu C M, Li H Z,et al.Dynamic recrystallization of high purity polycrystalline aluminum[J].Journal of Central South University of Technology:Natural Science Edition,2004,35(6):935-940.

服务与反馈：

【文章下载】【加入收藏】