锻压技术

快锻液压机传动系统合理性的探讨

英文标题：Research on the rationality of transmission system for fast forging hydraulic press

作者：陈超范淑琴赵升吨崔敏超韩晓兰

单位：西安交通大学

分类号：TG315.4

出版年,卷(期):页码：2016,41(2):6-11

摘要：

首先介绍了快锻液压机的国内外研究现状，指出了国内快锻液压机发展的不足。又分别分析了阀控液压传动系统、泵控液压传动系统和伺服液压传动系统的结构和原理，并以此为基础指出了3种液压传动系统的优缺点。相比于阀控液压传动系统和泵控液压传动系统，伺服液压传动系统具有伺服性能好、成本低、加工质量和精度高等优点。伺服液压系统非常适合应用于快锻液压机。最后总结了3种不同的液压传动系统的特点，指出伺服液压传动系统将成为快锻液压机传动系统的主要发展趋势。

The research status of fast forging hydraulic press at home and abroad was introduced, and deficiencies of the fast forging press in the domestic development were pointed out. The structures and principles of valve controlled hydraulic transmission system, pump controlled hydraulic transmission system and servo hydraulic transmission system were analyzed, and the advantages and disadvantages of these three kinds of hydraulic transmission system were pointed out on the above basis. Compared with valve controlled hydraulic transmission system and pump controlled hydraulic transmission system, servo hydraulic transmission system has the advantages of good servo performance, low cost, high processing quality and precision. Servo hydraulic transmission system is very suitable for fast forging hydraulic press. Finally, the characteristics of three different hydraulic transmission systems were summarized, and servo hydraulic transmission system was regarded as the main trend of development in fast forging hydraulic drive system.

基金项目：

国家自然科学基金资助项目（51305333）；陕西省科学技术研究发展计划工业攻关计划项目（2014K07-23）

陈超（1990-），男，博士研究生

参考文献：

[1]孟欣佳.快锻液压机的工作过程数值仿真与液压控制策略研究[D]. 秦皇岛：燕山大学，2009.Meng X J. Numerical Simulation of Working Process and Study of Hydraulic Control Strategy of A Fast Forging Hydraulic Press [D]. Qinhuangdao: Yanshan University, 2009.

[2]孙彩丽.20 MN快锻液压机设计及整体工作性能分析[D]. 秦皇岛：燕山大学，2007.Sun C L. Design and Whole Work Performance Analysis of 20 MN Quick Forging Hydranic Press [D]. Qinhuangdao: Yanshan University, 2007.

[3]Les Claar, Al Derouen, Bruno Stillhard. New life for hydraulic presses[J]. Engineering and Technology Guide, 1989,(12):40-46.

[4]Denman D, McNeil W. Multi-axial serbohydraulics controls compaction press[J]. Hydraulic & Pneumatics,2000,98(2):259-264.

[5]Lee Y H, Kopp R. Application for fuzzy control for a hydraulic forging machine[J]. Fuzzy Sets and Systems,2001,118:99-108.

[6]Lilly K W, Melligeri A S. Dynamic simulation and neural network complicane control of an intelligent forging center[J]. J. Intell. Robot. Syst.:Theory,1996,17:81-99.

[7]周斌，崔骁，李阁强.变排量直驱式液压系统在金属屑压块机中的应用研究[J].锻压技术，2014，39(12):71-78.Zhou B, Cui X, Li G Q. Research on application of the direct drive variable displacement hydraulic system in metal shaving press[J]. Forging & Stamping Technology，2014，39(12):71-78.

[8]周宇峰，谭建平，许洪韬，等.大型液压机卸压冲击影响因素研究[J].锻压技术，2015，40（11）：58-62.Zhou Y F，Tan J P，Xu H T，et al. Study of influential factors on decompression shock of large hydraulic press[J]. Forging & Stamping Technology，2015，40(11):58-62.

[9]艾超，孔祥东，刘胜凯，等.泵控液压机蓄能器快锻回路控制特性影响因素研究[J].锻压技术，2014，39（2）：88-95.Ai C, Kong X D, Liu S K, et al. Study on the influence factors of control characteristics of accumulator fast forging circuit for pump-controlled hydraulic press[J]. Forging & Stamping Technology，2014，39(2):88-95.

[10]王建军.20 MN快锻液压机关键部件结构分析[D]. 秦皇岛：燕山大学,2007.Wang J J. Structure Analysis of Key Parts of 20 MN Qucik Forging Hydraulic Press [D]. Qinhuangdao: Yanshan University, 2007.

[11]李贵闪，翟华.电液比例控制技术在液压机中的应用[J].锻压装备与制造技术，2005，40（6）：28-30.Li G S, Zhai H. Application of electro-hydro proportional control in hydraulic press [J]. China Metalforming Equipment & Manufacturing Technology, 2005,40(6):28-30.

[12]黄火兵，夏伟，屈盛官，等.比例控制与插装阀技术的应用与发展[J].机床与液压，2007,（4）：229-231.Huang H B, Xia W, Qu S G, et al. The application and development of proportional control and cartridge valve technology [J]. Machine Tool & Hydraulics, 2007,（4）：229-231.

[13]Tseknovich L I. Dynamics investigation for high-speed hydraulic press[J]. Metallurgical Plant and Technology,1995,88（6）:22-25.

[14]陈柏金，黄树槐.锻造液压机液压系统传动方式研究[J].锻压技术，2003，28（2）：44-47.Chen B J, Huang S H. Research on drive mode about hydraulic servo system of forging hydraulic press [J]. Forging & Stamping Technology,2003,28(2):44-47.

[15]刘忠伟，刘少军，黄明辉，等.巨型模锻液压机同步控制系统控制性能影响因素研究[J].锻压技术，2010，35（10）：64-68.Liu Z W，Liu S J，Huang M H，et al. Influence factors research on control performance of synchronous control system for giant forging hydraulic press[J]. Forging & Stamping Technology，2010，35(5):64-68.

[16]姚静.锻造液压机液压控制系统关键技术研究[D]. 秦皇岛：燕山大学，2009.Yao J. Research on Key Technology of Hydraulic Control System in Forging Oil Press [D]. Qinhuangdao: Yanshan University, 2009.

[17]李源.31.5 MN快锻液压机液压系统研究[D].重庆：重庆大学，2011.Li Y. Research on Hydraulic System of 31.5 MN Fast Forging Press [D]. Chongqing: Chongqing University,2011.

[18]陈刚.0.6 MN正弦泵控液压机蓄能器快锻子系统研究[D]. 秦皇岛：燕山大学，2013.Chen G.The Study on Accumulator Fast Forging Subsystem of 0.6 MN Sinusoidal Pump-Controllde Press[D]. Qinhuangdao: Yanshan University, 2013.

[19]徐平，沈佳兴，王慧.四径向轮齿轮泵优化设计及仿真[J].流体机械，2015,43（1）：33-37.Xu P, Shen J X, Wang H. Optimization design and simulation of four radial gear pump [J]. Fluid Machinery, 2015,43（1）：33-37.

[20]赵继云，杨存智，赵亮，等.矢量控制变频液压容积节流调速系统仿真研究[J].中国机械工程，2008，19（17）：2037-2040.Zhao J Y, Yang C Z, Zhao L, et al. Performance simulation of a vector control variable frequency hydraulic system with the combination of a throttle and variable displacement speed control [J]. China Mechanical Engineering, 2008,19（17）：2037-2040.

[21]丁问司，张旭，袁林燕.基于AMESim的交流正弦液压泵动态特性仿真分析[J].液压与气动，2013，（11）：29-32.Ding W S, Zhang X, Yuan L Y. Simulation analysis of dynamic characteristics of sinusoidal pump based on AMESim [J]. Chinese Hydraulics & Pneumatics, 2013，（11）：29-32.

[22]张旭.交流正弦液压泵动态性能设计与分析[D].广州：华南理工大学，2014.Zhang X. Design and Analysis of Dynamic Performance of Alternating Sinusoidal Pump[D].Guangzhou: South China University of Technology,2014.

[23]窦雪川.22 MN快锻液压机快锻系统理论与实验研究[D].秦皇岛：燕山大学，2009.Dou X C. Heoretical and Experimental Research on the Fast Forging System of 22 MN Fast Forging Press [D]. Qinhuangdao: Yanshan University, 2009.

[24]魏树国.开关磁阻电动机直驱定量泵控式液压机关键技术的研究[D].西安：西安交通大学，2009.Wei S G. Research on Key Techniques of the Hydraulic Press with Constant Delivery Pump Directly Controlled by Switched Reluctance Motor[D]. Xi'an: Xi'an Jiaotong University, 2009.

[25]李旭.新型开式快速伺服液压机及其动态特性的研究[D].西安：西安交通大学，2008.Li X. Research on A New Type of Open-Back High Speed Servo-Hydraulic Press and Dynamic Characteristic[D]. Xi'an: Xi'an Jiaotong University, 2008.

[26]赵升吨，范淑琴，李靖祥，等.一种交流伺服直驱增压式三层活塞电动液压缸及增压方法:中国专利,103148046A[P].2013-06-12.Zhao S D，Fan S Q，Li J X，et al. A servo direct drive booster type three layer piston electric hydraulic cylinder and pressure boosting method:China Patent,103148046A[P].2013-06-12.

[27]赵升吨，陈超，崔敏超，等.交流伺服压力机的研究现状与发展趋势[J].锻压技术，2015，40（2）:1-8.Zhao S D，Chen C，Cui M C, et al. Research status and development tendency of AC servo press[J]. Forging & Stamping Technology，2015，40(2):1-8.

服务与反馈：

【文章下载】【加入收藏】