锻压技术

凹圆弧母线筒形件空心旋压成形有限元模拟研究

英文标题：Research on finite element simulation of hollow spinning for tubular part with concave arc generatrix

作者：吴豪贾震韩志仁戚兴江高铁军

单位：沈阳航空航天大学

分类号：TG376

出版年,卷(期):页码：2016,41(2):84-90

摘要：

采用空心旋压工艺成形凹圆弧母线筒形件难度很大。利用有限元模拟手段对该成形过程进行预测性研究，为后续的实验与生产提供理论依据。首先理论推导单一道次凹圆弧型旋轮运动关系方程，再以此为边界条件进行模拟。研究中提出了3种旋压方法，通过对比分析模拟结果发现，随动芯轴可控制筒坯自由端金属流动均衡性，多道次成形由于每一道次的相对径向进给量小，有利于控制弧顶部位的褶皱，获得较好的壁厚均匀性，且旋压件弧顶横截面椭圆化较轻。

It is difficult to form the tubular part with concave arc generatrix by hollow spinning. The finite element simulation method was adopted to forecast the forming process of the tubular part with concave arc generatrix, and a theoretical basis for subsequent experiments and production was obtained. Firstly, the motion relationship equations of single pass concave arc roller were deduced theoretically. Then the equations were used as boundary conditions to simulate. Three kinds of spinning methods were proposed. Comparing the simulation results with analysis, it shows that the equilibrium of the free end metal flow of the tubular blank can be controlled by the dynamic mandrel. Due to the smaller relative radial feed in each pass, multi-pass spinning contributes to the wrinkles control of the arc portion and better thickness uniformity. And the ovalization of the cross section on the arc top is also smaller by multi-pass spinning.

基金项目：

航空科学基金(2014ZE54024)；沈阳航空航天大学大学生创新训练计划项目(DCX143409)

吴豪（1992-），男，本科贾震（1980-），男，博士，讲师

参考文献：

[1]夏琴香. 三维非轴对称零件旋压成形机理研究[J]. 机械工程学报, 2004, 40(2): 153-156.Xia Q X. Investigation on the mechanism of the spinning technology of the 3D non-axisymmetric parts [J]. Chinese Journal of Mechanical Engineering, 2004, 40(2): 153-156.

[2]Chang W S, Rajesh S R, Chun C K, et al. Microstructure and mechanical properties of hybrid laser-friction stir welding between AA6061-T6 Al alloy and AZ31 Mg alloy [J]. Journal of Materials Science and Technology, 2011, 27(3): 199-204.

[3]王国振，王春明，王军，等．间隙对5754铝合金激光填丝搭接焊气孔的影响[J]. 中国激光，2012, 39(12): 1203001-1-6.Wang G Z, Wang C M, Wang J, et al. Effects of gap on porosity during laser lap welding with filler wire of Al 5754 sheets [J]. Chinese Journal of Lasers, 2012, 39(12): 1203001-1-6.

[4]赵云豪. 旋压技术现状[J]. 锻压技术，2005, 30(5): 95-97.Zhao Y H. Present situation of spinning technology [J]. Forging & Stamping Technology, 2005, 30(5): 95-97.

[5]曾超，张赛军，夏琴香，等．旋轮轨迹和工艺参数对多道次拉深旋压成形质量的影响研究[J]. 锻压技术，2014, 39(1): 58-63.Zeng C, Zhang S J, Xia Q X, et al. Research on effect of roller-races and process parameters on multi-pass drawing spinning quality [J]. Forging & Stamping Technology, 2014, 39(1): 58-63.

[6]张美君，刘福贺．铝合金多楔带轮旋压成形数值分析与试验研究[J]. 锻压技术，2015, 40(2): 79-86.Zhang M J, Liu F H. Numerical analysis and experimental study on spinning forming of Al alloy multiple V-groove pulley [J]. Forging & Stamping Technology, 2015, 40(2): 79-86.

[7]Xia Q X, Xie S W, Huo Y L, et al. Numerical simulation and experimental research on the multi-pass neck-spinning of non-axisymmetric offset tube[J]. Journal of Materials Processing Technology, 2008, 206(1): 500-508.

[8]程秀全, 冯万林, 夏琴香. 非轴对称管件缩径旋压的数值模拟与参数优化的研究[J]. 塑性工程学报, 2008, 15(4): 61-66.Cheng X Q, Feng W L, Xia Q X. The study on the numerical simulation of non-axisymmetric tube neck-spinning and process parameters optimization [J]. Journal of Plasticity Engineering, 2008, 15(4): 61-66.

[9]Jiang S Y, Ren Z Y, Bin W U, et al. General issues of FEM in backward ball spinning of thin-walled tubular part with longitudinal inner ribs [J]. Transactions of Nonferrous Metals Society of China, 2007, 17(4): 793-798.

[10]Jiang S Y, Zheng Y F, Ren Z Y, et al. Multi-pass spinning of thin-walled tubular part with longitudinal inner ribs [J]. Transactions of Nonferrous Metals Society of China, 2009, 19(1): 215-221.

[11]Huang C C, Hung J C, Liao C C, et al. The Influence of the roller forming path on the neck-spinning process of tube at elevated temperature [A]. Proceedings of the ASME IMECE2011[C]. Colorado, USA, 2011.

[12]Kwiatkowski L, Melsheimer O. Wenzel S, et al. Experimental investigation of tool path strategies for incremental necking-in [J]. Int. J. Mater. Form., 2010, 3(1): 967-970.

[13]Sun L Y, Ye B Y, Xia Q X, et al. Analysis on forming characteristics of cup-shaped thin-walled inner gear spinning [J]. Key Engineering Materials, 2011, 455: 544-547.

[14]Li Y, Wang J, Lu G D, et al. A numerical study of the effects of roller paths on dimensional precision in die-less spinning of sheet metal [J]. Journal of Zhejiang University SCIENCE A, 2014, 15(6): 432-446.

[15]Jia Z, Han Z R, Xu Q, et al. Effects of processing parameters on the surface quality of square section die-less spinning [J]. Int. J. Adv. Manuf. Technol.,2015,80:1689-1700.

[16]丁韡，张康生，杨翠苹，等. 楔横轧成形等内径空心轴的椭圆度影响规律[J]. 塑性工程学报, 2010, 17(3): 27-31.Ding W, Zhang K S, Yang C P, et al. Study on the ovality of hollow shafts with equal inner diameter formed by CROSS wedge rolling [J]. Journal of Plasticity Engineering, 2010, 17(3): 27-31.

服务与反馈：

【文章下载】【加入收藏】