锻压技术

基于AutoForm的轮毂外包板拉延筋设置及板料优化

英文标题：Design of drawbeads and optimization of blank for hub hood fender based on Autoform

作者：余际星石向阳刘凯刘明文尹作虎

单位：武汉理工大学

关键词：轮毂外包板 AutoForm 拉延拉延筋

分类号：TG386

出版年,卷(期):页码：2016,41(2):45-50

摘要：

轮毂外包板为一弧状拉延件，工件拉延的局部起皱、破裂和拉深不足均源自流动不均匀。利用AutoForm软件模拟拉延过程，比较分段、整段与整圈3种结构拉延筋，发现整圈拉延筋效果最好，最大增厚率从3.32%降到1.18%，起皱消除。按流动均匀原则优化板坯形状，将板坯直角边改为圆弧，形成扇形板坯。研究结果表明，整圈拉延筋+扇形板坯设计，拉延最大增厚率与减薄率分别为0.56%与19.3%，缺陷消除，并得到合格产品。

The shape of the hub hood fender automobile panel is arc, so it is easy to wrinkle, rupture and form inadequately during its forming because of the non-uniformity material flow. The drawing process was numerically simulated by Autoform software, and the best effect of the deformation was gained through the closed circuit drawbead by comparing three different drawbeads design, namely sections, open circuit and closed circuit. Therefore, the maximum thickening rate decreased from 3.32% to 1.18%, and the wrinkle disappeared on the panel. Furthermore, the blank shape was optimized according to the material flow rule, namely, all right angle sides were modified by circular arc to form fan-shaped blank. The results show that with the design of closed circuit drawbead and fan-shaped blank, the maximum thickening rate and thinning rate is 0.56% and 19.3% respectively, and the qualified products are obtained without defection.

基金项目：

湖北省自然科学基金资助项目（2015CFB167）

余际星(1957-)，男，硕士，副教授石向阳（1990-），男，硕士研究生

参考文献：

[1]史刚．拉延筋技术[J]．模具技术，2004，(3)：31-33．Shi G. Drawbead technology[J]. Die and Mould Technology, 2004，(4):31-33.

[2]马晓春，沈卫兵．有限元数值模拟技术在汽车冲压件成形中的应用[J]．浙江工业大学学报，2007，(1)：100-104．Ma X C, Shen W B. Application of numerical simulation of finite element in molding process of automobile pressing parts [J]. Journal of Zhejiang University of Technology,2007，(1):100-104.

[3]陈邦华，夏玉峰，杜婉婉．成形图在汽车内板件冲压中的应用[J]．热加工工艺，2014，43(17)：122-124．Chen B H, Xia Y F, Du W W. Application of forming diagram in auto inner panels stamping process[J]. Hot Working Technology,2014,43(17):122-124.

[4]李奇涵，王文广，邓义，等. 基于数值模拟的油箱底壳拉延筋设置与优化[J]．锻压技术，2014，39(12)：31-39.Li Q H, Wang W G, Deng Y, et al. Design and optimization of drawbead of oil based on numerical simulation[J]. Forging & Stamping Technology,2014，39(12):31-39.

[5]古成中，吴新跃. 有限元网格划分及发展趋势[J]. 计算机科学与探索，2008，(3):248-259.Gu C Z, Wu X Y. A review of FEM and trend of development[J]. Journal of Frontiers of Computer Science and Technology,2008，(3):248-259.

[6]陈涛，高晖，李光耀，等．真实拉延筋参数化建模及其在薄板冲压仿真中的应用[J]．中国机械工程，2006，17(S1)：22-26.Chen T, Gao H, Li G Y, et al. New method of modeling drawbead geometry and its application in sheet metal forming[J]. China Mechanical Engineering,2006，17(S1):22-26.

[7]印雄飞，何丹农，彭颖红，等．板料成形有限元分析中的等拉延筋模型[J]．锻压装备与制造技术，1999，34(5)：49-51．Yin X F, He D N, Peng Y H, et al. Equivalent drawbead model in FEA of sheet forming[J]. China Metalforming Equipment & Manufacturing Technology,1999,34(5):49-51.

[8]李恩．汽车前轮罩拉深成形工艺研究[D]．合肥：合肥工业大学，2010．Li E. Study on Drawing Process of Front Wheel Cowling of the Automobile[D]. Hefei:Hefei University of Technology，2010.

[9]刘志军，梁秀强，卢宁．汽车冲压件起皱叠料问题的解决方案[J]．模具制造，2015，(2):20-23.Liu Z J, Liang X Q, Lu N. Solutions for the wrinkling and folding problem of automobile stamping parts[J]. Die & Mould Manufacture,2015，(2):20-23.

[10]孙琳琳．板料拉深中的拉延筋设置规律研究[D]．济南：山东大学，2006．Sun L L. Experimental Research on Regulation of Darwbead Installation in the Sheet Meatl Drawnig[D]. Ji'nan: Shandong University,2006.

服务与反馈：

【文章下载】【加入收藏】