锻压技术

基于正交试验的冲压成形工艺参数多目标优化

英文标题：Multi-objective optimization on stamping process parameters based on orthogonal test

作者：夏江梅张黎文琍

分类号：TG386.1

出版年,卷(期):页码：2016,41(3):33-36

摘要：

以某车型的前隔板为研究对象，通过三维建模软件设计工艺补充面和压料面，借助有限软件对其成形工序进行模拟分析。将数值模拟和正交试验设计相结合，采用多目标优化方法优化前隔板零件成形工序的压边力和各段拉延筋阻力系数，得到优化的参数组合为压边力F=500 kN，拉延筋阻力系数K1 =0.4，K2=0.4，K3 =0.3，K4=0.6。极差分析表明，对最大减薄率影响最大的因素为拉延筋阻力系数K2，对最大增厚率影响最大的因素为拉延筋阻力系数K3。实验结果表明，采用优化后的参数得到实际成形零件无拉裂缺陷且零件厚度满足要求。

For the dash board of automobile, the addendum surface and binder surface were designed by three-dimensional software, and the forming process was simulated and analyzed by finite element software. Combining the numerical simulation with the orthogonal experiment, the blank holder force and resistance coefficient of draw-bead were optimized in the forming process by a multi-objective optimization method. Furthermore, the optimized combination parameters were obtained when F=500 kN，K1 =0.4，K2=0.4，K3=0.3，K4=0.6 respectively. The extreme difference analysis shows that the draw-bead resistance coefficient K2 is the biggest influence factor on the maximum thinning rate, and the draw-bead resistance coefficient K3 is the biggest influence factor on the maximum thickening rate. The experimental results show that the part can meet the thickness requirements and avoid cracking after optimization.

基金项目：

重庆市教委资助项目(0637335)

夏江梅（1966-），女，硕士，副教授

参考文献：

［1］周猷. 基于仿真分析的车身覆盖件冲压成形质量研究[D]. 长沙：湖南大学, 2010.Zhou Y. Research on Quality of Automobile Body Panel Stamping Forming Based on Simulation Analysis[D]. Changsha:Hunan University, 2010.
［2］Papeleux L, Ponthot J. Finite element simulation of springback in sheet metal forming[J]. Journal of Materials Processing Technology,2002,(125-126): 785-791.
［3］王晓路，陈炜，高霖，等. 数值模拟对薄板冲压成形工艺设计的优化[J]. 锻压技术,2005, 30(3): 21-25.Wang X L, Chen W, Gao L, et al. Process design optimization of sheet metal forming by numerical simulation [J]. Forging & Stamping Technology,2005, 30(3): 21-25.
［4］赵茂俞，薛克敏，李萍. 多目标质量的覆盖件成形工艺参数优化[J]. 机械工程学报, 2009, 45(8): 276-282.Zhao M Y, Xue K M, Li P. Auto panel forming process parameters optimization of multi-objective quality[J]. Journal of Mechanical Engineering,2009, 45(8): 276-282.
［5］王列亮，郑燕萍，闫盖，等. 基于正交试验的拉延筋阻力优化[J]. 热加工工艺, 2014, 43(5): 142-144.Wang L L, Zheng Y P, Yan G, et al. Optimization of drawbead resistance based on orthogonal experiment[J]. Hot Working Technology,2014, 43(5): 142-144.
［6］张渝,丁波,马军伟. 基于正交试验的热冲压冷却过程数值模拟分析[J]. 锻压技术,2015,40(3):105-109.Zhang Y, Ding B, Ma J W. Numerical simulation of hot stamping cooling process based on orthogonal experiment[J]. Forging & Stamping Technology, 2015, 40(3):105-109.
［7］Wang H, Zhou J, Luo Y, et al. Forming of ellipse heads of large-scale austenitic stainless steel pressure vessel[J]. Procedia Engineering,2014, 81: 837-842.

服务与反馈：

【文章下载】【加入收藏】