锻压技术

首道次压下率对不锈钢热轧复合板界面结合性的影响

英文标题：Influence of first reduction ratio on the interfacial bonding properties of composite plate of hot rolled stainless steel

作者：王浩程晓茹付松岳王煜兰昆邱俊

单位：武汉科技大学

关键词：不锈钢复合板有限元首道次压下率最大垂直压应力界面结合率

分类号：

出版年,卷(期):页码：2016,41(4):19-24

摘要：

应用ABAQUS模拟了1200 ℃条件下的316L不锈钢/Q235碳钢复合板的首道次轧制过程，以最大垂直压应力与硬金属的平面变形抗力的比值作为复合板结合性的判断依据，得到了不同压下率的界面结合率。与实验数据对比发现，在相同的压下率情况下模拟的界面结合率略高。为了消除模拟结果与实验结果之间的差异，使有限元模型更接近于实验，用模拟数据和实验数据对判别式的比值进行修正，并得到比值为1.03975。修正后所得到的界面结合率更接近于实验结果；实验结果也验证了有限元模型的正确性和模拟过程中判断依据的可行性；此外，得到了界面结合率随首道次压下率的增加基本呈指数型增加的规律。

The first pass rolling process of stainless steel 316L and carbon steel Q235 composite plate at 1200 ℃ was simulated by software ABAQUS. The ratio between the maximum vertical compressive stress and the plane deformation resistance of hard metal was used to evaluate the bonding properties of the composite plate, and the rates of the interfacial bond with different pressures were obtained. Compared with the experimental data, the simulated results of the interfacial bond are a little higher under the same compression rate. In order to eliminate the difference between the simulated results and the experimental results to make the simulated results closer to the experimental results, the ratio of the discriminant was amended to 1.03975 based on both the simulated data and experimental data. The interface bonding ratio was closer to experimental results after amendment. The validity of the finite element model and the feasibility of the evaluation in the simulation process were verified by the experimental results. In addition, the interface binding rate increased exponentially with the increase of the first reduction rate.

基金项目：

国家自然科学基金面上项目(51274154) ；武汉科技大学研究生创新创业基金资助项目（JCX0054）

王浩（1988-），男，硕士研究生

参考文献：

[1]井玉安,王晨宇.不锈钢复合板生产技术综述[J].鞍山科技大学学报,2007,30(6):590-594.

Jing Y A, Wang C Y, Survey on the production technology of stainless steel clad plate[J]，Journal of Anshan University of Science and Technology ,2007,30(6):590-594.

[2]中国机械工程学会,中国材料研究学会,中国材料工程大典编委会.中国材料工程大典.第3 卷:(钢铁材料工程.下)[M].北京:化学工业出版社, 2006.

Chinese Mechanical Engineering Society,China Materials Research Society,Chinese Materials Engineering Canon Committee.Chinese Material Engineering.Volume Ⅲ（Iron and Steel Materials Engineering） [M].Beijing：Chemical Industry Press，2006.

[3]刘志亮,张文志.不锈钢复合板冷轧过程有限元模拟[J].机械科学与技术,2007,26(12):1588-1591.

Liu Z L ,Zhang W Z.Finite element simulation of cool rolling of stainless clad strips [J]. Mechanical Science and Technology for Aerospace Engineering, 2007,26(12):1588-1591.

[4]中国钢铁工业协会.钢铁行业2015-2025年技术发展预测[N].世界金属导报,2015.1.27(B08).

China Iron and Steel Industry Association. Steel industry 2015-2025 technology development forecast[N].The world Metal Bulletin,2015.1.27(B08).

[5]许秀梅,张文志,宗家富,等.基于有限元模拟的不锈钢/碳钢复合板极限压下量研究[J].重型机械,2003,(6):21-25.

Xu X M, Zhang W Z, Zong J F, et al. Investigation on extreme reduction in cold rolling of stainless steel/steel clad bases on FE simulation[J].Heavy Machinery, 2003,(6):21-25.

[6]程挺宇.不锈钢/碳钢热轧复合工艺及性能[J].上海金属,2009,31(1):48-58.

Cheng T Y. The hot rolling process and property of stainless steel/carbon steel composite plate [J].Shanghai Metals, 2009, 31(1):48-58.

[7]任勇,程晓茹.轧制过程数学模型[M].北京：冶金工业出版社, 2008.

Ren Y, Cheng X R. Mathematical Model of Rolling Process [M], Beijing: Metallurgical Industry Press,2008.

[8]裴文娇,郭训忠,王文涛,等. 316L奥氏体不锈钢的高温流变行为[J].塑性工程学报,2014,21(3):104-110.

Pei W J, Guo X Z, Wang W T, et al. Flow behaviors of 316L stainless steel at high temperature[J].Journal of Plasticity Engineering, 2014,21(3):104-110.

[9]Sellars C M. M cTegart W J. On the mechanism of hot deformation [J]. Acta Metallurgica,1966, (14):1136-1138.

[10]谭真,郭广文.工程合金热物性[M]. 北京：冶金工业出版社, 1994.

Tan Z, Guo G W. Thermal Physical Properties of Engineering Alloys[M].Beijing:Metallurgical Industry Press,1994.

[11]宗家富,张文志,许秀梅,等.双金属板热轧复合模拟及最小相对压下量的确定[J]. 燕山大学学报,2005,29(1):27-33.

Zong J F, Zhang W Z, Xu X M,et al.Simulation on hot rolling compounding of two metal plates and determination of minimum relative reduction[J].Journal of Yanshan University,2005,29(1):27-33.

[12]季晓鹏.多层不锈钢/铝(合金)复合板热轧工艺有限元数值模拟研究[D].西安:西安建筑科技大学,2008.

Ji X P.FEM Simulation of Hot-rolling Process for Multi-layer Stainless Steel/Aluminum(aluminum alloy) Plates[D].Xian:Xian University of Architecture and Technology,2008.

[13]侯英武.不锈钢复合板冷轧过程有限元模拟[D].秦皇岛:燕山大学,2003.

Hou Y W. The FEM Simulation of Stainless Clad Strip Cool-rolled Process [D].Qinhuangdao: Yanshan University,2003.

[14]李世芸,张曙红,张代明.双金属复合带材轧制过程有限元模拟[J].中国有色金属学报,2001,11(6):1075- 1076.

Li S Y, Zhang S H, Zhang D M, Finite element simulation of the rolling process of double metal composite strip [J]. Chinese Journal of Nonferrous Metals,2001, 11(6):1075-1076.

[15]龚晓东.复合板在热轧粘合过程中的轧制特性[J].重钢技术,1990,30(2):63-73.

Gong X D. Rolling characteristics of composite plate during hot rolling[J]. CISC Technology, 1990,30(2):63-73.

[16]黄亮.不锈钢复合板热轧复合仿真及参数分析[D].秦皇岛:燕山大学,2004.

Huang L. Simulation and Parameter Analysis of Hot Compounding Rolling of Stainless Clad Plate[D].Qinhuangdao:Yanshan University,2004.

[17]GB/T 6396—2008, 复合钢板力学及工艺性能试验方法[S].

GB/T 6396—2008,Clad steel plates-mechanical and technological test [S].

服务与反馈：

【文章下载】【加入收藏】