锻压技术

基于牛顿迭代算法的伺服压力机控制系统研究

英文标题：Study on servo press control system based on Newton iteration method

作者：洪瑞叶春生

单位：华中科技大学

分类号：TP273

出版年,卷(期):页码：2016,41(12):82-87

摘要：

为了实现伺服压力机滑块位移在特定工艺条件下的精确控制，以四连杆压力机为研究对象，以实现拉深工艺曲线为例，提出了基于牛顿迭代法伺服控制系统的设计方案。通过几何方法建立曲柄转角-滑块位移的数学方程式，得到运动学方程并进行仿真，根据仿真数据拟合出曲柄转角-滑块位移的数学关系式；利用MATLAB软件拟合目标工艺曲线，基于牛顿迭代算法实现了利用滑块位移对曲柄转角的多点一次性精确求解，并进一步利用计算结果拟合出曲柄转角-时间的函数；推导出控制周期内目标工艺曲线滑块位移对应的脉冲频率与个数，利用STM32实现输出目标脉冲。研究结果表明，目标工艺曲线与滑块实际位移曲线基本吻合，证明了该控制系统的设计方案可以实现对滑块位移的精确控制。

In order to realize the precise control of the slider displacement under specific conditions, a set of servo control system design scheme based on Newton iteration method was put forward to obtain drawing process curve for four-bar linkage press. Therefore, the mathematical equation of crank angle and sliding block displacement was established by geometric method, and the kinematic equations were derived and simulated. Then, the mathematics relationship between the crank angle and the sliding block displacement based on fitting the simulation data was obtained, and its multi-point and one-time accurate solution was realized by fitting the target process curve with MATLAB and based on Newton iterative algorithm. Furthermore, the function of crank angle and time was fit by the calculation results. Finally, the frequency and pulse number for the target process curve (slider block displacement)during one regulating period were derived, and target pulse was output by STM32. The research results show that the target process curve is consistent with the actual displacement of the slider, and the precise control of the sliding block displacement can be realized.

基金项目：

基金项目:国家自然科学基金资助项目（51375190）

作者简介：洪瑞（1990-），男，硕士 E-mail：hongrui_hust@foxmail.com 通讯作者：叶春生（1962-），男，博士，副教授 E-mail：csyehust@126.com

参考文献：

［1］Osakada K, Mori K, Altan T, et al. Mechanical servo press technology for metal forming
［J］. CIRP Annals-Manufacturing Technology, 2011, 60(2):651-672.

［2］李麟, 叶春生, 莫健华. 基于ARM的伺服压力机网络控制系统设计
［J］. 锻压技术, 2013,38(3):102-106.

Li L, Ye C S, Mo J H. Network control system design of servo press based on ARM
［J］. Forging & Stamping Technology, 2013,38(3):102-106.

［3］周洋, 叶春生, 莫健华. 肘杆式伺服压力机运动学仿真与工艺轨迹规划
［J］. 锻压装备与制造技术, 2012, 47(3):37-41.

Zhou Y, Ye C S, Mo J H. Toggle servo press kinematics simulation and trajectory planning process
［J］. China Metalforming Equipment & Manufacturing Technology, 2012, 47(3): 37-41.

［4］雷培, 刘云霞. 基于MATLAB的四连杆机构运动分析
［J］. 机械工程与自动化, 2009,(2):74-75.

Lei P, Liu Y X. Kinematical analysis of a four-bar mechanism using MATLAB
［J］. Mechanical Engineering and Automation, 2009,(2):74-75.

［5］俞伟洋, 叶春生. 基于MATLAB的四连杆伺服压力机控制求解
［J］. 锻压技术, 2015, 40(9):69-73.

Yu W Y, Ye C S. Research on the control solving of four-bar link servo press based on MATLAB
［J］. Forging & Stamping Technology, 2015, 40(9):69-73.

［6］唐家德. MATLAB在非线性曲线拟合中的应用研究
［J］. 智能计算机与应用, 2008,(1):57-59.

Tang J D. Research on the application of MATLAB in nonlinear curve fitting
［J］. Intelligent Computer and Application, 2008,(1):57-59.

［7］Dantchev S, Alhatib F. Nonlinear curve fitting for bioelectrical impedance data analysis: a minimum ellipsoid volume method
［J］. Physiological Measurement, 1999, 20(1):N1-9.

［8］Niu Q. Numerical continuation method for nonlinear curve fitting by use of least square method
［J］. Journal of Hehai University, 2003, 31(5):597-600.

［9］柳辉. 解非线性方程的牛顿迭代法及其应用
［J］. 重庆工学院学报:自然科学版, 2007, 21(8):95-98.

Liu H. Newton iterative method for solving nonlinear equations and its application
［J］. Journal of Chongqing Institute of Technology: Natural Science Edition, 2007, 21(8):95-98.

［10］Chun C. Construction of Newton-like iteration methods for solving nonlinear equations
［J］. Numerische Mathematik, 2006, 104(3):297-315.

服务与反馈：

【文章下载】【加入收藏】