锻压技术

高强度钢筋弯箍回弹角及箍筋精度研究

英文标题：Analysis on hoop-bending springback angle and hooping precision for high strength steel bar

作者：尚仲平刘志亮陈康元

单位：燕山大学

分类号：TG316

出版年,卷(期):页码：2017,42(1):155-160

摘要：

高强度钢筋在弯箍机上进行弯箍加工成一定角度后，在残余应力作用下钢筋会产生回弹现象。为了提高箍筋角度的精度，需要考虑回弹角度对箍筋角度的影响。基于弹塑性弯曲回弹理论，考虑加工硬化影响的情况下，推导出箍筋角度与回弹角度的关系式。并基于弯箍转盘几何模型，推导出弯箍转盘转角与箍筋角度的关系。应用MARC有限元软件建立弯箍模型，分析了弯箍成形速度、弯箍轴回转半径对钢筋回弹角的影响。进行弯箍成形实验，结果表明，弯箍成形速度对回弹角度影响较小，回弹角随着弯箍轴回转半径的增大而增大，实验结果与有限元模拟结果基本吻合。

When high strength steel bar hoop is bent into a certain angle in the hoop-bending machine, it can produce springback under the action of residual stress. Therefore, springback angle should be taken into consideration in order to improve the precision of hooping angle. According to springback elastic-plastic theory and considering the influence of work hardening, the relationship between hooping angle and springback angle was deduced, and the relationship between rotation angle and hooping angle was obtained based on the geometric model of hoop-bending rotary table. Furthermore, the model of hoop-bending was established by the finite element analysis software MARC, and the influence of hoop-bending speed and trurning radius of the hoop-bending axis on springback angle was analyzed. Finally, hoop-bending experiments were carried out. The results show that the hoop-bending speed has little effect on the springback angle, and the springback angle increases with the increase of turning radius of the hoop-bending axis. At the same time, the finite element simulation results are consistent with the experimental results.

基金项目：

秦皇岛市科学技术研究与发展计划项目(201502A013)

尚仲平（1964-），男，硕士，副教授 E-mail：WSQ3885061@126.com 通讯作者：刘志亮（1962-），男，博士，副教授 E-mail:zhiliangliu@ysu.edu.cn

参考文献：

[1]杨才福. 高强度建筑钢筋的最新技术进展[J]. 钢铁,2010,45（11）：1-11.

Yang C F. Recent developments of high strength rebars for building [J]. Iron and Steel, 2010, 45 (11): 1-11.

[2]杨忠民. 建筑用钢筋品种与技术性能指标评述[J]. 钢铁,2013, 48（5）：1-6, 24.

Yang Z M. Commentary for varieties and technical performance of fixture wire[J]. Iron and Steel, 2013, 48 (5): 1-6, 24.

[3]阎淑丽, 杜世渊. 钢筋弯曲回弹试验及其数学模型校正[J]. 机械管理开发, 2010, 25(6）：68-69.

Yan S L, Du S Y. The rebar bending-resilience experiment and the correction of mathematical model[J]. Mechanical Manage-ment and Development, 2010,25 (6): 68-69.

[4]陈康元. 钢筋矫直切断弯箍成形机理及仿真研究[D]. 秦皇岛:燕山大学，2014.

Chen K Y. Study of Forming Mechanism and Simulation of Steel Bar Straighteningg Cutting Hoop[D]. Qinhuangdao:Yanshan Unirersity,2014.

[5]薛克敏, 陈龙, 孔炎, 等. CLAM钢U形弯曲回弹数值模拟优化与试验[J]. 塑性工程学报, 2013, 20（1）：53-57.

Xue K M, Chen L, Kong Y, et al. Numerical simulation optimization and experimental study on U-bending springback of CLAM steel[J]. Journal of Plastic Engineering, 2013,20 (1): 53-57.

[6]张深. 小直径厚壁管材变曲率弯曲回弹控制研究[D]. 西安: 西北工业大学, 2014.

Zhang S. Springback Prediction and Compensation of Variable Curvature Bending for Minor Diameter Thick-Walled Tube [D]. Xi′an: Northwestern Polytechnical University, 2014.

[7]倪洪启, 刘相华, 王国栋. 超级钢板材V型弯曲回弹的数值模拟[J]. 钢铁研究学报, 2006,18(4)：26-28.

Ni H Q, Liu X H, Wang G D. Numerical simulation of V-bending springback of super steel plate [J]. Journal of Iron and Steel Research, 2006,18 (4):26-28.

[8]于庆波, 赵贤平, 孙斌, 等. 高层建筑用钢板的屈强比[J]. 钢铁, 2007, 42(11)：74-78.

Yu Q B, Zhao X P, Sun B, et al. Yield-strength ratio of steel plate for high-rise building[J]. Iron and Steel, 2007,42 (11):74-78.

[9]周翠兰, 刘红梅, 白晋钢, 等. 冷轧变形量对304不锈钢力学性能的影响[J]. 钢铁, 2012, 47(10)：70-75.

Zhou C L, Liu H M, Bai J G, et al. Effects of the cold-rolled reduction on the mechanical properties of 304 austenitic stainless steel sheets[J]. Iron and Steel,2007,47(10): 70-75.

[10]Jia Y Q, Liang Y L, Chen A Y, et al. Strain hardening of a layered and nanostructured AISI 304 strainless steel[J]. Journal of Iron and Steel Research: International, 2014, 21(4): 439-443.

[11]张春生. 变截面细长轴矫直辊型及矫直精度研究[D]. 秦皇岛: 燕山大学, 2012.

Zhang C S. Study on Roll Shape and Accuracy of Non-Uniform Slende Axle Parts Straightening[D]. Qinhuangdao: Yanshan University, 2012.

[12]郑夕健, 李允鹏, 常晓华. 钢筋弯曲回弹角度影响因素及修正[J]. 设计研究, 2014,（6）：59-61.

Zheng X J, Li Y P, Chang X H. Analysis of rebound angles factors for vertical bending steel and rebound angle correction [J]. Design & Research, 2014, (6): 59-61.

[13]杨才福, 张永权, 柳书平. 钒、氮微合金化钢筋强化机制[J]. 钢铁, 2001, 36(5): 55-57, 78.

Yang C F, Zhang Y Q, Liu S P. Strengthening mechanism in V-N micro-alloyed reinforcing bar steels [J]. Iron and Steel, 2001,36 (5): 55-57, 78.

服务与反馈：

【文章下载】【加入收藏】