锻压技术

空调翅片的翻边孔多道次成形模拟

英文标题：Simulation on multi-step hole-flanging for air-conditioning fins

作者：郭飞鹏李大永唐鼎

单位：上海交通大学

分类号：TG386

出版年,卷(期):页码：2017,42(5):164-170

摘要：

由于采用薄铝箔制造的空调翅片在成形过程中翻边孔孔壁容易出现破裂，且成形道次多通过经验确定，难以合理调整加工参数。采用有限元仿真方法，重现翻边孔的成形过程，分析缺陷的形成原因。建立了铝翅片多道次成形仿真模型，模拟了鼓包拉深工序、冲孔拉深工序和二次翻边工序的过程，并与实际铝翅片的翻边孔进行对比，验证了仿真结果的准确性，最后基于仿真结果探讨板料与模具之间的摩擦系数对成形结果的影响。实验表明，摩擦系数的改变会影响翻边孔成形中的厚度分布、最大减薄率以及翻边孔的成形质量。

The air-conditioning fins produced by thin aluminum foils are prone to fracture at hole wall during the hole-flanging, and forming steps are confirmed by experience, so the process parameters are hard to adjust reasonably. Therefore, the process of hole-flanging was simulated by FEA, and the cause of fracture was analyzed. Then, a multi-step hole-flanging model was set up, and drawing, piercing-drawing and twice flanges were simulated. Next, a simulation result was contrasted with real fins and verified. At last, the influences of friction coefficient between die and sheet on multi-step hole-flanging were elaborated according to the simulation result. The result indicates that different friction coefficients can affect the thickness distribution, the maximum thinning ratio and forming quality in the hole-flanging process.

基金项目：

国家科技支撑计划（2012BAF01B06）

郭飞鹏（1990-），男，硕士研究生李大永（1973-），男，博士，教授，博士生导师

参考文献：

［1］隽海昌，李廷强，杜建，等. 家用空调热交换器的发展[J]. 制冷与空调，2012，(2)：12-17.Juan H C, Li T Q, Du J, et al. The development of household air conditioner heat-exchanger[J]. Refrigeration and Air-Conditioning, 2012，(2)：12-17.
［2］刘援，王雷，韵晋琦. 中国房间空气调节器行业节能减排潜力分析[J]. 气候变化研究进展，2015, 11(3)：206-211.Liu Y, Wang L, Yun J Q. Analysis of energy efficiency and emission reduction potentials of room air conditioning sector of China[J]. Progressus Inquisitiones de Mutatione Climatis, 2015, 11(3)：206-211.
［3］靳林宝. 空调铝箔翅片成型过程缺陷简析[J]．轻合金加工技术，2011，39 (5): 55-57．Jin L B．Analysis on the defects produced during the aluminum foil fin for the air conditioner performing[J]. Light Alloy Fabrication Technology，2011，39 (5): 55-57.
［4］胡玄通，夏琴香，龙晓彬，等. 空调换热器翅片多工位级进模设计[J]．模具制造，2013，13 (11) : 10-14．Hu X T, Xia Q X, Long X B, et al. Design of multi-position progressive die for heat exchanger fin of air conditioner[J]. Mold Manufacturing, 2013，13 (11) : 10-14．
［5］熊盛勇，夏琴香，陈亚兵，等. 基于数值模拟的空调换热器翅片多道次级进拉深成形过程研究[J]. 锻压技术，2015，40(1): 27-32.Xiong S Y, Xia Q X, Chen Y B, et al. Research on multi-step progressive drawing of conditioner heat exchanger fin based on numerical simulation[J]. Forging & Stamping Technology, 2015，40(1): 27-32.
［6］杨守军，陈政弘，王红彬，等. 球底筒形件表面摩擦系数对拉深成形影响的数值模拟[J]. 锻压装备与制造技术，2014，49(6): 62-65.Yang S J, Chen Z H, Wang H B, et al. Numerical simulation of effect of friction coefficient about the spherical bottomed cylindrical parts surface on deep drawing process[J]. China Metalforming Equipment & Manufacturing Technology, 2014，49(6): 62-65.
［7］罗亚军，汪锐，何丹农，等. 板料拉深成形过程中摩擦系数的确定[J]. 上海交通大学学报，2015，35(7): 969-971.Lou Y J, Wang R, He D N, et al. Determination of friction coefficient in sheet metal deep drawing[J]. Journal of Shanghai Jiaotong University，2015，35(7): 969-971.
［8］崔国栋. 空调器散热片用铝箔的开发与质量控制[J]. 家用电器科技, 2000, (11):49-52.Cui G D. Devolopement and quality control of aluminum foils of conditioner heat-exchanger[J]. Science and Technology of Household Electric Appliance，2000, (11): 49-52.
［9］管连仲. 空调铝箔成形性研究及翅片冲压缺陷分析[D]. 长沙：中南大学，2002.Guan L Z. Study on Forming Conditioner Aluminum Foils and Stumping Defect Anlysis[D]. Changsha：Central South University，2002.
［10］GB/T 228.1—2010，金属材料拉伸试验第1部分：室温试验方法[S].GB/T 228.1—2010，Metallic materials—Tensile testing—Part 1: Method of test at room temperature[S].
［11］Barlat F, Lian K. Plastic behavior and stretchability of sheet metals. Part I: A yield function for orthotropic sheets under plane stress conditions[J]. International Journal of Plasticity, 1989, 5(1): 51-66.
［12］王敬伟. 基于DYNAFORM的AZ31鎂合金零件拉深成形过程模拟与预测[D]．太原: 太原理工大学，2012．Wang J W．Research on the Simulation and Prediction of the Deep Drawing Process of AZ31 Magnesium Alloy Sheet based on Dynaform[D]．Taiyuan: Taiyuan University of Technology，2012．
［13］夏琴香，魏光明，叶福源，等. 多工位级进冲压全工序数值模拟关键技术研究[J]．华南理工大学学报，2012，40(7):62-66．Xia Q X，Wei G M，Ye F Y，et al．Investigation into key technologies of numerical simulation of whole process chain during multi-position progressive stamping [J]. Journal of South China University of Technology，2012，40(7) : 62-66．
［14］陈伟，赵丕植，邹立颖，等. Fe含量对连续铸轧AA8079合金箔材晶粒组织和拉伸性能的影响[J]. 有色金属加工, 2015，44(4):14-18．Chen W, Zhao P Z, Zou L Y, et al. Effects of Fe content on grain structure and tensile properties of continuous casting AA8079 aluminum foil[J]. Nonferrous Metals Processing，2015，44(4) :14-18．
［15］叶茂. 金属塑性加工中摩擦润滑原理及应用[M]. 沈阳：东北工学院出版社，1990．Ye M. The Principle and Application of Friction and Lubrication in Metal Plastic Processing [M]. Shenyang: Northeastern University of Technology Press，1990．

服务与反馈：

【文章下载】【加入收藏】