锻压技术

某新能源汽车外板件的工艺参数优化

英文标题：Optimization on process parameters for outer panel of a new energy vehicle

作者：邓长勇谭伟田铁

分类号：TG386.1

出版年,卷(期):页码：2017,42(8):38-41

摘要：

针对某新能源汽车车尾门外板成形过程中易发生的起皱、破裂和成形不足等缺陷，借助试验软件Design-Expert和数值模拟软件AutoForm对该车尾门外板进行试验设计。试验设计时，将摩擦系数μ和成形时的压机下行速度v、压边力Fb作为优化因素，以最大减薄率、最大增厚率和成形不足比作为评价目标，对其工艺参数进行优化，借助多目标优化，得出最优的参数组合为：摩擦系数μ=0.15、成形时的压机下行速度v=10 mm·s-1、压边力Fb=1.6×103 kN。最后采用试模进行验证，并对得到的零件进行检测，零件无拉裂和起皱缺陷，且成形充分，表明本文所提出的方法可以有效地为汽车外板件模具开发提供参考。

For the defects of wrinkling, rupture and inadequate forming produced in the forming process for the outer panel of a new energy vehicle, experience design was conducted by Design-Expert software and finite element simulation software AutoForm. Then, friction coefficient μ, press down speed v and blank hold force Fb were set as influence factors, and the maximum thinning rate, the maximum thickening rate and the forming defect ratio were used as the target. Therefore, the process parameters were optimized. Furthermore, the optimal parameter combination was obtained by multi-objective optimization with μ=0.15, v=10 mm·s-1, Fb=1.6×103 kN. Finally, the test mode was verified, and parts without crack and wrinkle defects are formed fully. Thus, the proposed method can provide reference for the development of vehicle outer panel parts effectively.

基金项目：

重庆市科委商用车变速器协同创新与关键技术攻关项目(cstc2012jcsf-jfzhX0027)；重庆市高等学校青年骨干教师项目 (No.2016-46)

邓长勇（1982-），男，硕士，副教授

参考文献：

［1］李轩颖,徐雪峰,付春林,等.某型飞机钛合金钣金件热冲压成形工艺参数优化[J].塑性工程学报,2017,24(1):92-97.Li X Y, Xu X F, Fu C L, et al. Optimization of hot stamping process parameters for a certain type of aircraft titanium alloy sheet metal parts [J]. Journal of Plasticity Engineering, 2017, 24(1):92-97.
［2］高利平,汪木兰. 基于正交试验的离合器波形片冲压成形工艺参数优化[J]. 锻压技术,2015,40（11）:32-35.Gao L P, Wang M L. Optimization of stamping process parameters for cushion segment based on orthogonal experiment [J]. Forging & Stamping Technology, 2015,40（11）:32-35.
［3］杨谊丽，陈文琳，崔礼春.尾门外板冲压成形数值模拟及伺服拉深实验[J]. 锻压技术，2016，41（3）：153-157.Yang Y L，Chen W L，Cui L C. Numerical simulation of forming process for tail-gate outer panel and its servo drawing experiment [J]. Forging & Stamping Technology，2016，41（3）：153-157.
［4］李文平.汽车顶盖前横梁拉延成形工艺数值模拟分析[J].塑性工程学报,2017,24(2):118-121.Li W P. Numerical simulation analysis on drawing forming process of front cross member of automobile top cover [J]. Journal of Plasticity Engineering, 2017, 24(2):118-121.
［5］倪昀,黄亚玲,章跃洪. 基于DYNAFORM汽车覆盖件冲压仿真分析[J]. 热加工工艺,2011,40(11):108-111.Ni Y, Huang Y L, Zhang Y H. Stamping simulation analysis of auto-body panels based on DYNAFORM[J]. Hot Working Technology,2011,40(11):108-111.
［6］谢晖,罗红专,钟志华. 板料冲压成型CAE中拉裂的预测研究及应用[J]. 湖南大学学报：自然科学版，2005, 32(2):17-20.Xie H, Luo H Z, Zhong Z H. Prediction and application of fractures in CAE of sheet forming[J]. Journal of Hunan University：Natural Sciences, 2005, 32(2):17-20.
［7］黄跃东,邱晓刚. 汽车顶盖冲压成型的CAE模拟研究[J]. 汽车技术,2011,(6):54-58.Huang Y D, Qiu X G. Study on CAE simulation of auto roof panel stamping forming process [J]. Automobile Technology, 2011,(6):54-58.

服务与反馈：

【文章下载】【加入收藏】