锻压技术

汽车前地板后段零件拉延成形工艺参数优化

英文标题：Optimization on drawing process parameters for rear parts of automobile front floor

作者：曾利奎李彩霞王敬

分类号：TG386.1

出版年,卷(期):页码：2017,42(8):42-44

摘要：

为了提高汽车前地板后段拉延成形件的成形品质，借助有限元软件AutoForm，建立零件拉延成形过程的有限元模型进行数值模拟。采用正交试验设计和数值模拟相结合的方法，对拉延成形工艺参数进行优化。在数值模拟分析中，以零件的最大减薄率作为开裂指标，以最大起皱准则作为起皱指标，最后采用多目标优化方法得出最优的工艺参数组合。并将得到的最优参数进行实验验证，实验结果表明，本文提出的方法可以有效地控制汽车前地板后段零件拉延成形的开裂和起皱缺陷。

In order to improve the forming quality of rear part of automobile front floor, a finite element model of the drawing process was established, and the drawing process was simulated by finite element software AutoForm. Then, the drawing technological parameters were optimized by combining the orthogonal experiment design with numerical simulation. During the analysis of simulation, the maximum thinning rate was used to reflect cracking index, and the maximum wrinkling criterion was used to reflect the wrinkling index. Finally, the optimal combination of process parameters was obtained by the multi-objective optimization method, and the optimal parameters were verified by experiment. The experimental results show that the proposed method can effectively control the cracking and wrinkle of automobile front floor rear part.

基金项目：

重庆市教委科学技术研究项目（KJ1503906）

曾利奎(1971-)，男，学士，高级讲师

参考文献：

［1］陈继涛，宋海燕，朱永强. 基于Dynaform的汽车发动机盖内板成形分析[J]. 锻压技术，2017，42(1): 19-22.Chen J T, Song H Y, Zhu Y Q. Analysis on drawing process of automotive engine hood inner panel based on Dynaform[J]. Forging & Stamping Technology，2017，42(1): 19-22.
［2］王列亮，郑燕萍，闫盖，等. 基于正交试验的拉延筋阻力优化[J]. 热加工工艺，2014, 43(5): 142-144.Wang L L, Zheng Y P, Yan G, et al. Optimization of drawbead resistance based on orthogonal experiment[J]. Hot Working Technology，2014, 43(5): 142-144.
［3］翁茂荣，李强，曹淼龙. 汽车前地板单动拉延成形工艺分析与数值模拟[J]. 锻压技术，2015, 40(5): 48-51.Weng M R, Li Q, Cao M L. Process analysis and numerical simulation on single drawing for automobile front floor[J]. Forging & Stamping Technology，2015, 40(5): 48-51.
［4］沙海,胡建华,罗昱,等. 轮罩外板的冲压数值模拟与拉延筋优化[J]. 锻压装备与制造技术,2016,51(4):81-84.Sha H, Hu J H, Luo Y, et al. Stamping numerical simulation and drawbead optimization for outer panel of wheel cover [J]. China Metalforming Equipment & Manufacturing Technology, 2016, 51(4):81-84.
［5］涂小文. AutoForm原理技巧与战例实用手册[M]. 武汉：湖北科学技术出版社, 2013.Tu X W. AutoForm Principle and Practice of Practical Manual [M]. Wuhan：Hubei Science and Technology Press, 2013.

服务与反馈：

【文章下载】【加入收藏】