锻压技术

锥台复合截面环件精密轧制毛坯的优化设计方法

英文标题：Optimization design on precision rolling blank for conical ring with outer step

作者：何松华林兰箭钱东升

单位：武汉理工大学

分类号：TG33

出版年,卷(期):页码：2017,42(8):54-61

摘要：

针对广泛用于油气管道阀门、航空发动机机匣及结合环中的锥台复合截面环件较难同时获得所需的直径尺寸和台阶形状的问题，提出“等壁厚型”和“变壁厚型”两种环坯设计方法。借助ABAQUS模拟平台，建立两种轧制环坯设计下的锥台复合截面环件轧制过程的有限元仿真模型，分析两种环坯轧制过程中的台阶充型规律及最终的成形环件尺寸误差。结果表明，“变壁厚型”环坯比“等壁厚型”环坯轧制成形后尺寸精度高。为获得最优的尺寸精度，在“变壁厚型”环坯设计基础上，添加尺寸修正系数η。通过对比不同修正系数η下的环坯轧制成形尺寸精度，得出尺寸修正系数η在1<η<1.1范围内的“变壁厚型”环坯为最优环件轧制毛坯。基于模拟结果，在WD51Y-250多功能轧环机上进行锥台复合截面环件轧制实验，验证有限元模拟的可靠性和环坯设计方案的可行性。

The conical rings with outer step is widely used in oil and gas pipeline valves, bearings and aircraft engine casings. Since it is difficult to obtain the required diameter size and step shape simultaneously, two kinds of ring blanks with equal wall thickness and variable wall thickness were designed. Then, their rolling process was simulated by the ABAQUS, and the step filling law and the dimension errors of the rolled ring were analyzed. The results show that the dimension precision of rolled ring with variable wall thicknesses ring blank is higher than that of rolled ring with equal wall thickness ring. Therefore, the size correction coefficient η is added to obtain the optimal dimension precision based on the variable thickness design. Finally, by comparing the dimensional precision of rolled ring under different correction coefficients η, the optimal correction coefficient is within 1<η<1.1. According to simulation result, related rolling experiments were carried out in WD51Y-250 ring rolling mill to verify the reliability of FE simulation and the feasibility of the design method of blank with variable wall thicknesses.

基金项目：

江苏省重点研发专项（BE2016009）；JGXM（201607GC01）

何松（1990-），男，硕士研究生华林（1962-），男，博士，教授

参考文献：

［1］华林，黄兴高，朱春东.环件轧制理论和技术[M].北京：机械工业出版社，2001.Hua L，Huang X G，Zhu C D. Ring Rolling Theory and Technology[M].Beijing: China Machine Press，2001.
［2］韩星会, 华林, 兰箭,等. 内台阶锥形环件轧制三维有限元模拟和工艺优化设计[J]. 中国机械工程, 2007, 18(16):1979-1983.Han X H, Hua L, Lan J, et al. 3D FEM simulation and optimization design of rolling process of conical ring with inner steps [J]. China Mechanical Engineering，2007, 18(16):1979-1983.
［3］Qian D S, Hua L. Blank design optimization for T-section ring rolling [J]. Ironmak & Steelmak，2009，36(6):462-469.
［4］Deng J, Mao H. A blank optimization design method for three-roll cross rolling of complex-groove and small-hole ring[J]. International Journal of Mechanical Sciences, 2015, 93:218-228.
［5］Park M, Lee C, Lee J. Development of L-sectioned ring for construction machines by profile ring rolling process[J]. International Journal of Precision Engineering and Manufacturing, 2016, 17(2):233-240.
［6］陈孝庆，郭良刚，杨合，等. TC4钛合金锥形环辗轧坯料仿真优化设计[J].塑性工程学报，2014，21(2): 25-31.Chen X Q, Guo L G，Yang H, et al. Study on blank optimization design of conical ring rolling process for TC4 titanium ally by numerical simulation[J]. Journal of Plasticity Engineering，2014，21(2): 25-31.
［7］龚小涛, 杨帆, 郭红星. 复杂异形环件毛坯优化设计方法研究[J]. 锻压技术, 2012, 37(2):75-78.Gong X T，Yang F，Guo H X.Study on optimization design method of complex shaped ring blank [J].Forging & Stamping Technology，2012，37 (2):75-78.
［8］韩双, 钱东升. 铝合金锥面筒形环件轧制成形数值模拟与实验研究[J]. 锻压技术, 2016, 41(9):64-70.Han S，Qian D S. Numerical simulation and experimental study on aluminum alloy tapered cylindrical ring in roll forming [J]. Forging & Stamping Technology, 2016, 41(9):64-70.
［9］Guo L, Yang H, Zhan M. Research on plastic deformation behaviour in cold ring rolling by FEM numerical simulation [J]. Modeling & Simulation in Materials Science & Engineering, 2005, 13(7):1029-1046.
［10］Wang M, Li X, Du F, et al. Hot deformation of austenite and prediction of microstructure evolution of cross-wedge rolling [J]. Materials Science & Engineering A, 2004, 379(1-2):133-140.

服务与反馈：

【文章下载】【加入收藏】