锻压技术

基于Deform的热成形冷却系统优化

英文标题：Optimization on cooling system in the hot stamping based on Deform

作者：邹伟张立强

分类号：TG305

出版年,卷(期):页码：2017,42(9):30-34

摘要：

以22MnB5高强度钢U形件为例，建立B柱热冲压有限元模型，并通过Deform-3D软件对热冲压过程进行数值模拟。设定保压结束后U形件的最大减薄率以及最大温差作为评价指标，基于数值模拟和3因素5水平正交实验方法，分析了在多指标因素不同水平下冷却系统参数对保压结束后U形件的最大减薄率以及最大温差大小和分布规律的影响，获得参数的优化组合：冷却管道直径为Φ8.5 mm，两管道孔中心间距为30 mm，管道孔中心与模具型面距离为13 mm。通过热冲压实验，得到保压结束后U形件的最大温差为124.5 ℃，最大减薄率为4.73％，验证了优化参数组合的有效性，为热冲压模具冷却系统设计优化提供了理论参考。

For U-shaped part of high-strength steel 22MnB5, a finite element model of hot stamping for B-pillar was established, and the hot stamping process was simulated by Deform software. Then, the maximum thinning ratio and the maximum temperature difference of U-shaped part after holding pressure process were set as evaluation indexes, and the influences of cooling system parameters on their size and distribution were analyzed under different levels of the multi-index factors based on the numerical simulation and orthogonal experiment with three-factor and five-level. Finally, the optimal parameter combination was obtained with the pipeline diameter of Φ8.5 mm, the distance between two pipelines of 30 mm and the distance between the pipeline center and the die surface of 13 mm. The experimental results show that the maximum temperature difference of U-shaped part is 124.5 ℃, and the maximum thinning ratio is 4.73%. Thus, the feasibility of the optimal parameter combination is verified, and a theoretical reference is provided for the parameter design of cooling system in hot stamping dies.

基金项目：

湖南省教育厅资助科研项目(13B145)；湖南省大学生研究性学习和创新性实验计划项目；湖南省高校科技创新团队支持计划资助

作者简介：邹伟(1991-)，男，学士，硕士研究生 E-mail：429606865@qq.com 通讯作者：张立强(1978-)，男，博士，副教授 E-mail：zlq2k1103@126.com

参考文献：

［1］兰东东, 祁涛, 王祥. 高强度钢热成形模具冷却系统数值模拟[J]. 热加工工艺, 2014, 43(1): 132-133.

Lan D D, Qi T, Wang X. Numerical simulation of hot stamping die cooling system for high strength steel[J]. Hot Working Technology, 2014, 43(1): 132-133.

［2］许伟力, 艾健, 罗爱辉. 钢板热冲压新技术介绍[J]. 塑性工程学报, 2009, 16(4): 39-43.

Xu W L, Ai J, Luo A H. Introduction of sheet metal hot-forming[J]. Journal of Plasticity Engineering, 2009, 16(4): 39-43.

［3］Hoffmann H, So H, Steinbeiss H. Design of hot stamping tools with cooling system [J]. Annals of the CIRP, 2007, 56(1): 269-272.

［4］代尚军. 超高强度钢热成形模具冷却系统研究[D]. 长春: 吉林大学, 2014.

Dai S J. The Research on Hot Forming Tools Cooling System of HSS[D]. Changchun: Jilin University, 2014.

［5］于宏元. 车辆高强度钢板热冲压工艺改进研究及应用[D]. 大连: 大连理工大学, 2013.

Yu H Y. Research on Hot Forming Process Improvement of Automobile High Strength Steel and Its Application[D]. Dalian: Dalian University of Technology, 2013.

［6］Geiger M, Merklein M, Hoff C. Basic investigations on the hot stamping steel 22MnB5[J]. Advanced Materials Research, 2005, (6): 795-804.

［7］何育军, 谢延敏, 田银, 等. 热冲压成形数值仿真及模具冷却系统参数研[J]. 锻压技术, 2015, 40(11):148-154.

He Y J, Xie Y M, Tian Y, et al. Numerical simulation of hot stamping and parameter study of die cooling system[J]. Forging & Stamping Technology, 2015, 40(11):148-154.

［8］廖铮玮. 高强度钢热成形换热系数估算及试验研究[D]. 大连: 大连理工大学, 2013.

Liao Z W. Estimation and Experimental Study of Heat Transfer Coefficient in Hot Forming of Ultra High Strength Steels[D]. Dalian: Dalian University of Technology, 2013.

［9］Hay B A, Bourouga B, Dessain C. Thermal contact resistance estimation at the blank/tool interface: experimental approach to simulate the blank cooling during the hot stamping process[J]. International Journal of Material Forming, 2010, 3(3):147-163.

服务与反馈：

【文章下载】【加入收藏】