锻压技术

铝合金螺旋面挤压过程数值模拟及模具优化

英文标题：Numerical simulation and mold optimization on extrusion process of aluminum alloy spiral surface

作者：刘厚根赵贝贝夏峰

单位：中南大学

分类号：TG376

出版年,卷(期):页码：2017,42(12):169-174

摘要：

采用模拟软件Deform-3D基于热力耦合对6063铝合金螺旋面型材挤压成形过程进行模拟，获得了挤压过程中载荷-时间曲线、应变场、应力场、速度场及金属流动情况。结果表明，金属流出工作带后，在同一截面内的应力、应变分布不均，型材内部金属发生回弹运动，使螺旋面的螺旋升角变小。针对上述问题，提出在模具工作带后面增设可拆卸式矫正器的方法，保证铝合金螺旋面螺旋角度的精度。最后，通过实验验证了这一方法的可行性，模具优化后螺旋面螺旋升角由11.96°提高至20.99°，螺旋面精度提高了33.7%。

The extrusion process of aluminum alloy 6063 spiral profile was simulated by software Deform-3D based on the thermo-mechanical coupling, and the load time curve, strain field, stress field, velocity field and metal flow situation in the extrusion process were obtained. However, after the metal flowed out of working band, the stress and strain distribution of metal in the same cross section are uneven, and the springback movement occurres in internal metal of profile, which makes the spiral angle of the spiral surface smaller. For the above problems, the method of adding disassembly correction equipment at the back of working band of the mold was put forward to ensure the precision of spiral angle of the spiral surface for aluminum alloy. Finally, the feasibility of this method was verified by experiment. Thus, the spiral angle of the spiral surface is raised from 11.96° to 20.99° after mold optimization, and its accuracy is improved by 41%.

基金项目：

高性能复杂制造国家重点实验室自主探索基金（zzyjkt2013)；湖南省科技厅重点研发计划（2015GK3006）

作者简介：刘厚根（1959-），男，硕士，副教授 E-mail：lhg.csu@126.com

参考文献：

［1］刘厚根,李成佳.罗茨机械增压器渐开线型转子型线的改进研究[J]. 流体机械，2013，41（8）：49-51.

Liu H G，Li C J. Improvement of involute rotor profile of roots mechanical supercharger [J]. Fluid Machinery，2013，41(8)：49-51.

［2］梁世斌, 冯扬明, 陈泗文. 铝合金的可挤压性[J]. 轻合金加工技术, 2013, 41(12):37-39.

Liang S B，Feng Y M，Chen S W. Extrusion of aluminum alloy [J]. Light Alloy Processing Technology, 2013，41（12）：37-39.

［3］杨志高，徐永礼，庞祖高，等.基于Deform-3D方管铝合金型材等温挤压的变速挤压数值模拟 [J]. 锻压技术，2015，40（4）:152-155.

Yang Z G，Xu Y L，Pang Z G，et al. Numerical simulation of variable speed extrusion for isothermal extrusion process of aluminum alloy square tube btube based on Deform-3D. [J]. Forging ＆ Stamping Technology, 2015，2015, 40（4）: 152-155.

［4］徐磊，赵国群，张存生.多腔壁板铝型材挤压过程数值模拟及模具优化 [J]. 机械工程学报，2011，47（22）:63-66.

Xu L，Zhao G Q，Zhang C S. Numerical simulation and die optimization of extrusion process of multi cavitypanel aluminum profile [J]. Journal of Mechanical Engineering，2011，47（22）:63-66.

［5］李泽勇，张宝红，于建民.内六方空心件挤压成形金属流动规律研究[J].锻压技术，2014，39（3）：133-135.

Li Z Y，Zhang B H，Yu J M. Study on the law of metal flow in hexagonal square hollow. [J]. Forging ＆ Stamping Technology, 2014，39（3）：133-135.

［6］闫洪，包忠诩，柳和生.角铝型材挤压过程的数值模拟 [J]. 中国有色金属学报，2001，11（2）：202-205.

Yan H ，Bao Z X，Liu H S. Numerical simulation of extrusion process of aluminum profile [J]. Chinese Journal of Nonferrous Metals，2001，11（2）：202-205.

［7］徐宁，黄东男，李有来. 复杂断面空心型材的双级分流模挤压过程模拟分析 [J]. 锻压技术，2015，41（12）：62-65.

Xu N，Huang D N，Li Y L. Simulation analysis on two-stage porthole dies extrusion for complicated hollow section profile. [J]. Forging ＆ Stamping Technology, 2015，41（12）：62-65.

［8］陈天晓. 铝合金挤压的数值模拟及模具结构优化 [D]. 重庆：西南大学，2014.

Chen T X. Numerical Simulation of Aluminum Alloy Extrusion and Optimization of Die Structure [J].Chongqing: Southwestern University, 2014.

［9］Park Y B, Yoon J H, Yang D Y. Finite element analysis of steady-state three-dimensional helical extrusion of twisted sections using recurrent boundary conditions[J]. International Journal of Mechanical Sciences, 1994, 36(2):137-148.

［10］Gan C L, Zheng K H, Qi W J, et al. Constitutive equations for high temperature flow stress prediction of 6063 Al alloy considering compensation of strain[J]. Transactions of Nonferrous Metals Society of China, 2014, 24(11):3486-3491.

［11］翁剑成，刘国买，秦晓亮，等. 基于Deform 3D的铝棒材热力耦合挤压过程的数值模拟[J]. 龙岩学院学报, 2016, 34(2):81-85.

Wong J C，Liu G M，Qin X L, et al. Numerical simulation of thermomechanical coupling extrusion process of aluminum bars based on Deform-3D [J]. Journal of Longyan University，2016, 34（2）：81-85.

［12］田海洋，薛慧鹏，戴明.凹球面挤压成形回弹研究[J].热加工工艺，2016，45（11）:166-167.

Tian H Y，Xue H P，Dai M. Study on springback of extrusion process of concave spherical surface [J]. Hot Working Process，2016，45（11）:166-167.

服务与反馈：

【文章下载】【加入收藏】