锻压技术

铝合金前门加强板零件冲压成形数值模拟及参数优化

英文标题：Numerical simulation and parameter optimization on stamping process of front door reinforcing plate parts for aluminum alloy

作者：李桂琴卢仲珺

单位：上海大学

关键词：铝合金冲压破裂前门加强板数值模拟

分类号：TG146.2+1

出版年,卷(期):页码：2018,43(10):52-56

摘要：

为了消除某款采用6016铝合金材料生产的前门加强板零件的破裂缺陷，建立了分析模型，确定了拉延筋的强度、模具表面的摩擦系数、压边圈的压边力等因素对铝合金材料成形性能的影响。并通过正交试验法得出影响成形因素的主次顺序以及较优的参数组合。结果表明：模具压边圈的压边力对零件破裂影响最大，其次是模具表面摩擦系数，影响最小的是等效拉延筋强度。获取的调试参数组合为：等效拉延筋强度为66.0 N·mm-1，压边圈的压边力为950 kN，模具表面的摩擦系数为0.17。经过验证，模拟结果与实际生产结果具有较好的吻合度。数值模拟可减少铝合金零件调试过程中的不确定性，降低调试成本。

In order to eliminate cracking defects of front door reinforcing plate parts produced by 6016 aluminum alloy, the analysis model was established, and the influences of the drawbead strength, the friction coefficient on mold surface and the blank holder force on the forming properties of aluminum alloy material were determined. Then, the order of primary and secondary factors and the better combination of parameters influencing the forming factors were obtained by the orthogonal experiment method. The results show that the blank holder force has the greatest influence on the cracking of parts, followed by the friction coefficient on mold surface, and the least influence is the equivalent drawbead strength. The obtained debugging parameter combination is the equivalent drawbead strength of 66.0 N·mm-1, the blank holder force of 950 kN, and the friction coefficient on mold surface of 0.17. The experiments show that the simulation results have a better consistency with the actual production results, and the numerical simulation can reduce the uncertainty of aluminum alloy parts in debugging process and the debugging cost.

基金项目：

上海市重点学科建设项目资助（Y0102）

李桂琴（1965－），女，博士，副教授，E-mail：leeching@shu.edu.cn

参考文献：

[1]王冠，周佳，刘志文，等.铝合金汽车前碰撞横梁的轻量化设计与碰撞性能分析[J].中国有色金属学报,2012,22(1):90-98.

Wang G, Zhou J, Liu Z W, et al. Lightweight design and crash performance analysis of automotive aluminum bumper[J].The Chinese Journal of Nonferrous Metals,2012,22(1):90-98.

[2]Krichen A, Kacem A, Hbaieb M. Blank-holding effect on the hole-flanging process of sheet aluminum alloy[J].Journal of Materials Processing Technology,2011,211(4):619-626.

[3]Dasappa P, Inal K, Mishra R. The effects of anisotropic yield functions and their material parameters on prediction of forming limit diagrams[J].International Journal of Solids and Structures,2012,49(25):3528-3550.

[4]田野，吕明达，黄余平.汽车前门加强板冲压工艺参数优化[J].锻压技术,2014,39(12):35-38.

Tian Y, Lyu M D, Huang Y P. Parameter optimization of stamping process on auto front door reinforcing plate[J].Forging & Stamping Technology,2014,39(12):35-38.

[5]强军.汽车发罩内板成形工艺参数多目标优化[J].锻压技术，2016,41(4):41-44.

Qiang J. Multiobjective optimization on forming the automobile hood inner panel[J]. Forging & Stamping Technology, 2016, 41(4): 41-44.

[6]白有俊，刘世豪，苏思，等.汽车侧壁上外板冲压成形过程仿真及实验[J].锻压技术,2017,42(9):25-29.

Bai Y J, Liu S H, Su S, et al. Stamping process simulation and experiment of automotive side wall plate[J].Forging & Stamping Technology,2017,42(9):25-29.

[7]张海波，孙力伟.基于正交试验的车顶盖板冲压工艺参数模拟研究[J].锻压技术，2017,42(4):79-84.

Zhang H B, Sun L W. Simulation research on stamping technological parameters of roof cover plate based on orthogonal experiment[J].Forging & Stamping Technology,2017,42(4):79-84.

[8]谢晖，刘翔，王诗恩，等. 时效硬化对6021-T4铝板成形性影响及冲压工艺稳健设计[J]. 塑性工程学报，2016,23(1):21-26.

Xie H,Liu Ｘ,Wang S E, et al. Age hardening effect on formability of 6021-T4 aluminum and robust stamping process design[J]. Journal of Plasticity Engineering，2016,23(1):21-26.

[9]高云亮，缪卫东，冯昭伟，等. 几何参数对TiNi 合金血管支架支撑性能的影响[J]. 稀有金属，2017，41(1):8-13.

Gao Y L，Miao W D，Feng Z W, et al. TiNi alloy vascular stents′ supporting performance with different design geometric parameters[J]. Chinese Journal of Rare Metals，2017，41(1):8-13.

[10]伍杰，马增胜，阳习雨，等.镀层金属板冲压成形断裂失效的有限元模拟[J].锻压技术，2015,40(3):136-140.

Wu J, Ma Z S, Yang X Y, et al. Finite element simulation of fracture in stamping for coated metal sheet[J].Forging & Stamping Technology,2015,40(3):136-140.

服务与反馈：

【文章下载】【加入收藏】