锻压技术

高速动车组转向架侧梁上盖板成形缺陷研究

英文标题：Research on forming defects of steering frame side member upper

作者：梁继业张学广何广忠

分类号：TG302

出版年,卷(期):页码：2018,43(11):28-32

摘要：

为了提升高速动车组转向架侧梁上盖板的成形精度，通过Pamstamp-2G有限元软件对高速动车组转向架侧梁上盖板的冲压成形过程进行了数值模拟研究，分析了此类构件直线段弯曲、轮廓精度差及纵向侧弯等缺陷的成因，并提出了相应的缺陷控制措施。结果表明：采取反弯曲措施可以有效控制直线段的弯曲缺陷；基于回弹对模具进行补偿可以明显提高零件的轮廓精度；基于零件结构对成形模具设置导向装置可以有效控制纵向侧弯缺陷。利用所得的缺陷控制方法进行冲压成形试验，成形件直线段平直，轮廓精度良好，纵向侧弯缺陷消除，得到了高质量的成形件，验证了研究结果的正确性。

In order to improve the forming accuracy of steering frame side member upper cover plate in CRH train，its stamping process was simulated and analyzed by finite element software Pamstamp-2G. Then, the causes of forming defects such as the bending of straight line segment, low contour accuracy and longitudinal side bending were analyzed, and the corresponding control methods were proposed. The results show that the bending defect of straight line segment is controlled effectively by adopting the anti-bending method, and the contour accuracy is evidently improved based on the springback amount to compensate the die surfaces. Then, the longitudinal side bending defect is eliminated effectively by adding the guide device to the forming dies based on the structure of part. Furthermore, the forming tests were conducted by the obtained defect controlling methods, the straight-line and fine contour precision in the forming part were obtained, the longitudinal side bending defect was suppressed, and the high quality parts were obtained, which verify the correctness of the conclusions in this work.

基金项目：

国家自然科学基金资助项目（51575231）

梁继业（1965-），男，本科，高级工程师,E-mail：liangjiye@cccar.com.cn;通迅作者：张学广（1989-），男，博士，高级工程师,E-mail：zxg13@mails.jlu.edu.cn

参考文献：

[1]Vollersten F, Spenger A, Kraus J, et al. Extrusion, channel, and profile bending: A review [J]. Journal of Materials Processing Technology, 1999, 87(1-3): 1-27.

[2]朴明伟，张山，梁树林，等. 高铁运用经济速度与安全稳定裕度调控[J]. 振动工程学报, 2013, 26(6): 935-943.

Piao M W, Zhang S, Liang S L, et al. Economic velocity and safety stablility margin regulation for high-speed rail operation[J]. Journal of Vibration Engineering, 2013, 26(6): 935-943.

[3]滕靖，申博，费翔，等. 高铁车站公交接驳线路设计[J]. 系统工程理论与实践, 2013, 33(11): 2937-2944.

Teng J, Shen B, Fei X, et al. Designing feeder bus lines for high-speed railway terminals[J]. Systems Engineering-theory & Prac-tice, 2013, 33(11): 2937-2944.

[4]刘建强, 赵治博, 章国平, 等. 地铁车辆转向架轴承故障诊断方法研究[J]. 铁道学报, 2015, 37(1): 30-36.

Liu J Q, Zhao Z B, Zhang G P, et al. Research on fault diagnosis method for bogie bearing of metro vechicle[J]. Journal of the China Railway Society, 2015, 37(1): 30-36.

[5]王文静, 王燕, 孙守光, 等. 高速列车转向架载荷谱长期跟踪试验研究[J]. 西南交通大学学报, 2015, 50(1): 84-89.

Wang W J, Wang Y, Sun S G, et al. Long-term load spectrum test of high-speed train bogie[J]. Journal of Southwest Jiaotong University, 2015, 50(1): 84-89.

[6]刘婧瑶, 唐承统, 宁汝新. 薄壁管纯弯曲塑性成形分析及回弹计算[J]. 塑性工程学报, 2009, 16(2): 5-9,14.

Liu J Y, Tang C T, Ning R X. Plastic-formation analysis and springback calculating of thin-wall tube pure-bending[J]. Journal of Plasticity Engineering, 2009, 16(2): 5-9,14.

[7]冯杨, 兰凤崇, 阮锋. 基于补偿因子的复杂型面零件冲压回弹控制研究与应用（第Ⅰ部分：理论）[J]. 塑性工程学报, 2014, 21(6): 51-55.

Feng Y, Lan F C, Ruan F. Theoretical analysis and application research on compensation factors of sheet metal stamping springback (I: Theory)[J]. Journal of Plasticity Engineering, 2014, 21(6): 51-55.

[8]韩金全, 万敏, 李卫东. 基于回弹的飞机蒙皮拉形模型面修模技术研究[J]. 机械工程学报, 2009, 45(11): 184-188.

Han J Q, Wan M, Li W D. Surface improvement based on springback compensation for aircraft skin stretching tool[J]. Journal of Plasticity Engineering, 2009, 45(11): 184-188.

服务与反馈：

【文章下载】【加入收藏】