锻压技术

基于曲率积分法的方管矫直曲率解析研究

英文标题：Study on curvature analysis in square tube straightening process based on

作者：石祥刘志芳

单位：重庆理工大学

分类号：TG333.2

出版年,卷(期):页码：2018,43(11):53-58

摘要：

以方管的弯曲缺陷形式为研究对象，基于弹塑性弯曲变形的理论，以方管断面在两个相邻矫直辊之间的历程为研究区间，以曲率积分法为基础，建立了曲率和压下量的关系模型，并建立了该断面在矫直历程中弯曲、弹性恢复和反向再弯曲等过程的数学模型。然后利用Matlab的fsolve优化算法对所建立的模型进行求解。同时，利用大型商业软件MSC.Marc建立方管矫直过程的三维接触有限元模型，并进行了模拟仿真。然后进行了方管矫直实验。最终通过对矫直过程中的数值解析、有限元分析、实验验证3种研究方式的结果进行对比分析，以验证矫直解析模型的正确性与实用性。

For the bending defect of square tube, based on the theory of elastic-plastic bending deformation, the history of square tube section between two adjacent straightening rollers was taken as the research interval, and the relationship model between curvature and reduction was built by the curvature integration method. Then, the mathematical model was established to describe the process of bending, elastic recovery and reverse bending in the course of straightening of the section and solved by the fsolve optimization algorithm of Matlab. At the same time, a three-dimensional contact finite element model of the square tube straightening process was established by a large-scale commercial software MSC.Marc, and the simulation was conducted. Furthermore, the square tube straightening experiment was performed. Finally, the results of numerical analysis, finite element analysis and experimental verification during the straightening process were compared and analyzed to determine the correctness and practicality of the straightening analytical model.

基金项目：

重庆市教委科学技术研究项目资助（KJ1600941）

石祥（1991-），男，硕士研究生,E-mail：3046507723@qq.com;通讯作者：刘志芳(1984-)，男，博士，讲师,E-mail:liuzhifang@cqut.edu.cn

参考文献：

[1]崔甫. 矫直原理与矫直机械[M]. 北京: 冶金工业出版社, 2002.

Cui F．Straightening and Straightening Machine[M]．Beijing: Metallurgy Industry Press, 2002.

[2]崔丽红, 臧勇, 章博, 等. 多辊矫直过程中H型钢断面的应力演变规律[J]. 北京科技大学学报, 2008, 30(8): 942-946.

Cui L H, Zang Y, Zhang B, et al. Stress evolvement rule of an H-beam section during multi-roller straightening process[J]. Journal of University of Science and Technology Beijing, 2008, 30(8): 942-946.

[3]崔丽红, 臧勇, 章博, 等. H型钢精确矫直技术的研究分析[J]. 机械设计与制造, 2008, (4): 176-177.

Cui L H，Zang Y，Zhang B, et al. The investigation in H-beam precision straightening technology [J]. Machinery Design & Manufacture, 2008, (4): 176-177.

[4]Schleinzer G, Fischer F D. Residual stress formation during the roller straightening of railway rails[J]. International Journal of Mechanical Sciences, 2001, 43(10): 2281-2295.

[5]臧勇, 王会刚, 崔福龙. 型钢辊式矫直压弯挠度的弹塑性解析[J]. 机械工程学报, 2005, 41(11): 47-52.

Zang Y, Wang H G, Cui F L. Elastic-plasticity analyses of bending deflection on section roller straightening
［J］. Journal of Mechanical Engineering , 2005, 41(11): 47-52.

[6]薛军安, 胡贤磊, 刘相华, 等. 辊式矫直过程弹塑性弯曲数学模型[J]. 钢铁研究学报, 2008, 20(11): 33-36.

Xue J A, Hu X L, Liu X H, et al. Mathematical model of elastic-plastic bending for roller leveling[J]. Journal of Iron and Steel Research, 2008, 20(11): 33-36.

[7]王勇勤，刘志芳，严兴春. 中厚板热矫直过程中曲率的解析[J].钢铁，2012，47（1）：51-54,94.

Wang Y Q,Liu Z F, Yan X C. Curvature analysis for plate during hot leveling[J]. Iron and Steel,2012,47(1):51-54,94.

[8]Liu Z F, Wang Y Q, Yan X C. A new model for the plate leveling process based on curvature integration method[J]. Int.J. Mech.Sci., 2012, 54(1): 213-224.

[9]刘志芳.压下量对中厚板矫直过程中关键参数的影响[J].锻压技术, 2015, 40(5): 109-113.

Liu Z F. Influence of rolling reduction on key parameters in the straighteningprocess of plate[J]．Forging ＆ Stamping Technology, 2015, 40(5): 109-113.

[10]刘志芳.原始曲率对中厚板矫直过程中的关键参数影响[J]. 锻压技术, 2015, 40(10): 69-75.

Liu Z F. Influence of initial curvature on key parameters of plate during leveling process[J]．Forging ＆ Stamping Technology, 2015, 40(10): 69-75.

[11]刘志芳. 基于曲率积分法的板材矫直理论研究[D]. 重庆: 重庆大学, 2014.

Liu Z F. Study of Leveling Theory Based on Curvature Integration Method for Plates[D]. Chongqing: Chongqing University, 2014.

[12]李忠富, 臧勇, 王会刚. 型钢九辊矫直力能参数与压弯挠度关系解析[J]. 北京科技大学学报, 2004, 26(5): 542-544.

Li Z F, Zang Y, Wang H G. Relation between bending deflection of H-beam and energetic parameters of nine-roller straightening [J]. Journal of University of Science and Technology Beijing, 2004, 26(5): 542-544.

服务与反馈：

【文章下载】【加入收藏】