锻压技术

预拉伸对不同强度汽车用高强钢弯曲回弹的影响

英文标题：Influence of prestretching on bending springback of different high strength steels used in automobile

作者：章军1 2 李少博1 2 马闻宇1 2 王宝川1 2 郑学斌1 2 杨建炜1 2

分类号：TG386

出版年,卷(期):页码：2018,43(12):20-24

摘要：

The springback behavior of high strength steel used in automobile was investigated by experiment, and the influence of prestretching on springback of material was mainly analyzed. The specimens of HC330/590DH, HC340/590DP and HC420/780DP were prestretched respectively, and then the specimens were bended at three points after prestretching. Then, the springback angle was measured, and the strain, thinning, springback and microstructure were analyzed. The results show that for different prestretching amounts of the same material, the springback angle increases with the increase of the prestretching value. However, for the same type of high strength steel with different strengths, the springback increases with the increasing of material strength. After bending of HC340/590DP, the grain in the inner area is compressed, and the grain in the outer area is stretched. Therefore, for two materials with the same strength and different microstructures, the srpingback of DP steel is higher than that of DH steel.

基金项目：

基金项目:国家重点研发计划专项资助(2017YFB0304401)

作者简介：章军（1973- ），男，硕士，高级工程师 Email：zhangjun@shougang.com.cn 通讯作者：马闻宇（1988- ），男，博士，工程师 Email:wymaustb@163.com

参考文献：

参考文献:

［1］Wang J, Afshan S, Gkantou M, et al. Flexural behaviour of hotfinished high strength steel square and rectangular hollow sections
［J］. Journal of Constructional Steel Research, 2016, 121: 97-109.

［2］Ghaei A,Green D E, Aryanpour A. Springback simulation of advanced high strength steels considering nonlinear elastic unloadingreloading behavior
［J］. Materials and Design, 2015, 88: 461-470.

［3］刘铭心，张东民，吴艳云，等. 基于正交试验的座椅撑板冲压成形回弹研究及优化
［J］.锻压技术，2017, 42(12): 36-40.

Liu M X, Zhang D M, Wu Y Y, et al. Springback analysis and optimization on stamping for seat support plate based on orthogonal experiments
［J］. Forming & Stamping Technology,2017, 42(12): 36-40.

［4］Marretta L, Ingarao G, Di Lorenzo R. Design of sheet stamping operations to control springback and thinning: A multiobjective stochastic optimization approach
［J］. International Journal of Mechanical Sciences, 2010,52:914-927.

［5］Chongthairungruang B,Uthaisangsuk V, Suranuntchai S， et al. Experimental and numerical investigation of springback effect for advanced high strength dual phase steel
［J］. Materials and Design, 2012, 39: 318-328.

［6］Sumikawa S, Ishiwatari A，Hiramoto J. Improvement of springback prediction accuracy by considering nonlinear elastoplastic behavior after stress reversal
［J］. Journal of Materials Processing Technology, 2017, 241: 46-53.

［7］Ma W Y， Li T， Yao Y，et al. Study on the cold stamping of oil sump tank for the thickness and springback
［J］. IOP Conference Series: Materials Science and Engineering, 2018, 381: 955-959.

［8］Lim H, Lee M G, Sung J H,et al. Timedependent springback of advanced high strength steels
［J］. International Journal of Plasticity, 2012, 29: 42-59.

［9］Wang Jyhwen, Suhas Verma, Richard Alexander. Springback control of sheet metal air bending process
［J］.Journal of Manufacturing Processes, 2015,10:21-27.

服务与反馈：

【文章下载】【加入收藏】