锻压技术

角型截面不锈钢型材拉弯成形起皱缺陷控制

英文标题：Wrinkling defect control for stainless steel profile with angle section in stretchbending process

作者：谷诤巍贾磊

分类号：TG306

出版年,卷(期):页码：2018,43(12):39-43

摘要：

对某地铁车辆用角型截面变曲率不锈钢车顶弯梁的拉弯成形工艺进行了数值模拟研究，分析了此类构件产生起皱缺陷的原因，研究了型材立边高度、模具间隙及拉伸量对起皱趋势变化的影响规律，找到了最优的模具参数和工艺参数，最终通过试验进行了验证，获得了高质量的拉弯件。结果表明：立边高度对起皱缺陷影响显著，在固定弦边长度的情况下，增大立边高度将加重起皱缺陷；模具间隙对起皱情况有一定影响，减小模具间隙能够减轻起皱缺陷，但不能完全消除；拉伸量对起皱缺陷影响很大，增大拉伸量可以有效控制起皱缺陷，当拉伸量增加至7.5%时起皱缺陷基本消失。

The stretchbending process of stainless steel roof bending beam with angle section and variable curvature for a subway vehicle was studied by numerical simulation, and the causes of wrinkle defects in such components were analyzed. Then, the influences of sidewall height, die clearance and stretching amount on wrinkling trend were studied, and the optimum parameters of die and process were found. Finally, the verification test was carried out, and the high quality stretrchbending parts were obtained. The results show that the sidewall height has a significant influence on the wrinkling defect, and increasing the sidewall height can aggravate wrinkling defect when the length of flange is fixed. However, the die clearance has a certain influence on the wrinkling defect, and reducing the die clearance can reduce the wrinkling defect, but the wrinkling cannot be completely eliminated. The stretching amount has a great influence on the wrinkling defect, and increasing the stretching amount can effectively control the wrinkling. When the stretching amount increases to 7.5%, the wrinkling substantially disappears.

基金项目：

基金项目:国家自然科学基金资助项目（51101072）；吉林省科技发展计划项目（20160204058GX）

作者简介：谷诤巍（1970-），男，博士，教授 Email：guzhengwei20180525@163.com

参考文献：

参考文献:

［1］王胜满. 用于地铁车辆的不锈钢型材拉弯成形缺陷
［J］.吉林大学学报：工学版，2013,43（6）：1546-1550.

Wang S M. Stretch bend forming defects of stainless steel profiles of metro vehicles
［J］. Journal of Jilin University：Engineering and Technology Edition，2013, 43（6）:1546-1550.

［2］刁可山，周贤宾，李晓星，等. 矩形截面型材拉弯成形
［J］.北京航空航天大学学报，2005,31（2）：134-137.

Diao K S, Zhou X B, Li X X, et al. Stretch bending of aluminum extrusion
［J］. Journal of Beijing University of Aeronautics and Astronautics,2005,31（2）：134-137.

［3］薛克仲.城市轨道车辆车体材料选择
［J］. 城市轨道交通研究，2003,6（1）：14-19.

Xue K Z. Selection of car body materials for urban railway vehicles
［J］.Urban Mass Transit, 2003, 6（1）：14-19.

［4］Liu C G, Zhang X G, Wu X T, et al. Optimization of poststretching elongation in stretch bending of aluminum hollow profile
［J］. International Journal of Advanced Manufacturing Technology, 2016,82（9-12）：1737-1746.

［5］张学广，刘纯国，张石磊，等. 轴向非对称中空型材拉弯过渡区长度优化
［J］.哈尔滨工业大学学报，2015,47（10）：82-87.

Zhang X G, Liu C G, Zhang S L, et al. Optimization of transition zone length in stretch bending of axially asymmetric hollow profiles
［J］. Journal of Harbin Institute of Technology, 2015,47（10）：82-87.

［6］金朝海，周贤宾，刁可山，等. 铝合金矩形管拉弯成形过程的数值模拟
［J］.材料科学与工艺，2004,12（6）:572-575.

Jin C H, Zhou X B, Diao K S, et al. Numerical simulation of a Stretch bending process for extruded aluminum rectangular tubes
［J］. Materials Science & Technology, 2004,12（6）：572-575.

［7］金朝海，周贤宾，刁可山，等. 铝合金型材拉弯成形回弹的有限元模拟
［J］.材料科学与工艺，2004,12（4）:394-397.

Jin C H, Zhou X B, Diao K S, et al. Springback analysis for stretch bending of aluminum profile
［J］. Materials Science & Technology, 2004,12（4）:394-397.

［8］周贤宾，刁可山，李晓星，等. 闭截面型材的拉弯成形性
［J］.北京航空航天大学学报，2006，32（10）：1168-1173.

Zhou X B, Diao K S, Li X X, et al. Stretch bending formability of profile
［J］.Journal of Beijing University of Aeronautics and Astronautics，2006,32（10）：1168-1173.

［9］高宏志，周贤宾，李晓星，等. 型材拉弯成形性评估专家系统
［J］.计算机辅助设计与图形学学报，2008,20（11）：1411-1416.

Gao H Z, Zhou X B, Li X X, et al. An expert system for stretchbending formability evaluation of profiles
［J］.Journal of Computeraided Design and Computer Graphics，2008,20（11）：1411-1416.

服务与反馈：

【文章下载】【加入收藏】