锻压技术

断路保护器定位板四轴冲铆级进模设计

英文标题：Design on four-axis punching-riveting progressive die for locating plate of breaker protector

作者：郑清春秦晓军朱培浩刘静娜沈晓治

分类号：TG356.23

出版年,卷(期):页码：2019,44(3):90-93

摘要：

通过对断路保护器定位板的结构进行分析，制定了加工工艺方案及排样方案，设计了四轴冲铆级进模具，该级进模具包括导向机构、定位机构、冲孔机构、铆轴机构等。在结构优化上，采用销钉垂直度导块和销钉上限位柱进行定位，保证了销钉的垂直度和压入深度，提高了加工零件的精度；在设计方法上，选取双排导料柱作为导料系统，并配合装卡料带的缩径段使用，降低了料带前进的位置误差；此外，采用四轴同时铆钉的方式，大大提高了生产效率。实际生产证明，将冲孔和铆钉结合为一体是合理的，不仅省去了人工铆钉过程，降低了工人劳动强度，减少近60%成本投入，而且将产品合格率由原先的80%提高到近100%，生产效率提高近50%。

The processing schemes and layout schemes were formulated by analyzing the locating plate structure of breaker protector, and a four-axis punching-riveting progressive die was designed with guide mechanism, positioning mechanism, punching mechanism and riveting mechanism, etc. In the structural optimization, the positioning was set up by pin vertical guide block and the pin upper limit post to ensure the verticality and the penetration depth of the pin, and the accuracy of parts was improved. In the design method, the double-row guide column was chosen as the guide system, the reduced diameter section of the loaded strip was used together to reduce the position error of the strip forward. In addition, the production efficiency was greatly improved by using the four-axis simultaneous rivets. The actual production proves that it is reasonable to combine with punching and riveting, which not only saves the manual rivet process to lower the labor intensity of workers and reduce cost by nearly 60%, but also improves product yield from 80% to almost 100%, and production efficiency by nearly 50%.

基金项目：

天津市科技计划项目（17PTYPHZ00060）；天津市工业和信息化委员会专项资金资助项目（201803104）

郑清春（1971-），男，博士，教授，E-mail：zhengqingchun@tjut.edu.cn；通讯作者：朱培浩（1983-），男，博士，副教授，E-mail：zhupeihao_gp@163.com

参考文献：

［1］李兴文.低压断路器研发新技术综述
［J］.电器与能效管理技术,2015, (9):1-7,14.

Li X W. Review of the new research and development technologies for low voltage circuit breakers
［J］. Electrical & Energy Management Technology,2015, (9):1-7,14.

［2］马世博,侯瑞东,邵明杰,等.锁片件多工位级进模设计
［J］.锻压技术,2017,42(2):100-103.

Ma S B,Hou R D,Shao M J,et al. Design of multi-position progressive die for locking blade part
［J］. Forging ＆ Stamping Technology，2017,42(2):100-103.

［3］于仁萍,宫晓峰.夹板多工位级进模设计
［J］.锻压技术,2018,43(3):140-143.

Yu R P,Gong X F. Multi-position progressive die design for clamping plate
［J］. Forging ＆ Stamping Technology，2018,43(3):140-143.

［4］刘春雨,郑薇.保险杠安装支架级进模具的应用与研究
［J］.锻压技术,2017,42(5):91-95.

Liu C Y,Zheng W. Application and research on progressive dies for bumper mounting bracket
［J］. Forging ＆ Stamping Technology，2017,42(5):91-95.

［5］郑家贤.冲压工艺与模具设计实用手册
［M］. 北京：机械工业出版社，2007.

Zheng J X. Stamping Process and Die Design Handbook
［M］.Beijing: China Machine Press, 2007.

［6］丁文有,何晓聪,邢保英,等.铆向组合对双铆钉自冲铆接头力学性能的影响
［J］.塑性工程学报,2018,25(5):234-239.

Ding W Y,He X C,Xing B Y,et al. Effect of riveting orientation combination on mechanical properties of double rivet self-piercing riveted joint
［J］.Journal of Plasticity Engineering,2018,25(5):234-239.

［7］张祥林,张丽筠.精冲模具崩刃失效演变及机理分析
［J］.塑性工程学报,2018,25(5):33-38.

Zhang X L, Zhang L J. Evolution and mechanism analysis of chipping failure for fine blanking die
［J］. Journal of Plasticity Engineering, 2018,25(5):33-38.

［8］李巧敏,柳玉起,张秋翀.基于金属塑性成形理论的汽车覆盖件成形工艺智能优化方法
［J］.塑性工程学报,2018,25(5):60-65.

Li Q M,Liu Y Q,Zhang Q C. An intelligent optimization method for automobile panel forming based on metal plastic forming theory
［J］. Journal of Plasticity Engineering,2018,25(5):60-65.

［9］王宗申,管延锦,魏修亭,等.模具限制作用对工业纯铜模压变形影响的实验与理论研究
［J］.塑性工程学报,2017,24(6):143-150.

Wang Z S,Guan Y J,Wei X T,et al. Experimental and theoretical research on the influence of die constraint on groove pressing of commercially pure copper
［J］. Journal of Plasticity Engineering, 2017,24(6):143-150.

［10］工鹏驹，成虹.冲压模具设计师手册
［M］.北京:机械工业出版社，2009.

Wang P J，Cheng H. Stamping Die Design Handbook
［M］.Beijing：China Machine Press, 2009.

服务与反馈：

【文章下载】【加入收藏】