锻压技术

基于Dynaform的小半径弯管充液成形

英文标题：Hydroforming of elbow tube with small radius base on Dynaform

作者：蔡晋刘建邦

单位：沈阳航空航天大学

分类号：TG394

出版年,卷(期):页码：2019,44(8):86-91

摘要：

研究了304不锈钢小半径弯管充液成形。首先，通过计算得到了主要工艺参数：初始屈服压力、成形压力、整形压力以及轴向进给量的理论值。然后，建立了有限元模型，分析了主要工艺参数对成形质量的影响，优化了主要工艺参数。最后，利用优化后的工艺参数进行了实验，验证了该方法的可用性。研究结果表明：初始屈服压力过大或成形压力过大，会导致管壁过分减薄，弯管易发生破裂；成形压力过小或者轴向进给量过大，易导致弯管内侧形成褶皱；通过理论计算与数值模拟相结合的方法，可以实现成形工艺参数的最优化，为实现小半径弯管的充液成形提供了理论和技术支持。

The hydroforming of elbow tube with small radius for 304 stainless steel was studied. Firstly, the theoretical values of the main process parameters, such as initial yield pressure, forming pressure, shaping pressure and axial feeding amount, were obtained by calculation. Then, the finite element model was established, the influences of the main process parameters on the forming quality were analyzed, and the main process parameters were optimized. Finally, the feasibility of this method was verified by experiments with optimized process parameters. The results show that the excessive initial yield pressure or forming pressure leads to excessive thinning of tube wall and rupture of elbow tube, and too small forming pressure or too large axial feeding anount leads to wrinkle in the inner side of elbow tube easily. Furthermore, the optimization of forming process parameters are achieved by combining theoretical calculation with numerical simulation to provide theoretical and technical support for achieving the hydroforming of the elbow tube with small radius.

基金项目：

国家自然科学基金资助项目(51575364)

作者简介：蔡晋（1979-），男，博士，副教授 E-mail：saucai@163.com

参考文献：

[1] Shinde R A, Patil B T, Joshi K N. Optimization of tube hydroforming process (without axial feed) by using FEA simulations [J]. Procedia Technology, 2016, 23(5): 398-405.

[2] 苑世剑. 现代液压成形技术 [M]. 北京：国防工业出版社，2009.

Yuan S J. Modern Hydroforming Technology[M]. Beijing: National Defence Industry Press, 2009.

[3] Ko M, Allen T, Jiratheranat S, et al. The use of FEA and design of experiments to establish design guidelines for simple hydroformed parts [J]. International Journal of Machine tools and Manufacture, 2000, 40 (15): 2249-2266.

[4] Dohmann F, Hartl C. Hydroformingapplications of coherent FEsimulations to the development of products and processes[J]. Journal of Materials Processing Technology, 2004, 150 (1-2): 18-24.

[5] Parka J Y, Han S W, Jeong H S, et al. Advanced sealing system to prevent leakage in hydroforming[J]. Journal of Materials Processing Technology, 2017, 247(5): 103-110.

[6] 高铁军，刘青，蔡晋. 复杂形状TA2钛合金半管件黏性介质压力成形[J]. 中国有色金属学报，2016， 26(4)：790-796.

Gao T J, Liu Q, Cai J. Viscous pressure forming of semipipe parts of complex shape TA2 titanium alloy[J]. The Chinese Journal of Nonferrous Metals, 2016, 26(4): 790-796.

[7] Shinde R A, Patil B T, Joshi K N. Optimization of tube hydroforming process (without axial feed) by using FEA simulations[J]. Procedia Technology, 2016, 23(5): 398-405.

[8] AueULan Y, Ngaile G, Altan T. Optimizing tube hydroforming using process simulation and experimental verification[J]. Journal of Materials Processing Technology, 2004, 146(1): 137-143.

[9] Strano M, Jirathearanat S, Shr S G, et al. Virtual process development in tube hydroforming[J]. Journal of Materials Processing Technology, 2004, 146(1): 130-136.

[10]Strano M, Jirathearanat S, Altan T. Adaptive FEM simulation for tube hydroforming: A geometrybased approach for wrinkle detection[J]. CIRP Annals, 2001, 50(1): 185-190.

[11]Imaninejad M, Subhash G, Loukus A. Loading path optimization of tube hydroforming process[J]. International Journal of Machine Tools and Manufacture, 2005, 45(12-13): 1504-1514.

[12]Ko M. Investigation of the effect of loading path and variation in material properties on robustness of the tube hydroforming process[J]. Journal of Material Processing Technology, 2003, 113(3): 276-281.

[13]牟菊，门向南，陈清根，等. 基于ABAQUS有限元模拟铝合金小弯曲半径的内压推弯成形[J]. 热加工工艺，2015，44(13)：109-111.

Mou J, Men X N, Chen Q G, et al. Finite element simulation of aluminum alloy internal pressure bending forming with small radius based on ABAQUS[J]. Hot Working Technology, 2015, 44(13): 109-111.

[14]曾元松，李志强. 铝合金小弯曲半径管内压推弯成形过程的数值模拟[J]. 塑性工程学报，2003，10(2)：14-17.

Zeng Y S, Li Z Q. Numerical simulation of internal pressure bending forming process for aluminum alloy tube with small bending radius[J]. Journal of Plasticity Engineering, 2003, 10(2): 14-17.

[15]黄遐，曾元松，张新华，等. 不锈钢小弯曲半径管内压推弯成形过程有限元模拟[J]. 航空制造技术， 2005,34(10)：74-78.

Huang X, Zeng Y S, Zhang X H, et al. FEM simulation of internal pressure bending forming process for stainless steel tube with small bend radius[J]. Aeronautical Manufacturing Technology, 2005, 34 (10): 74-78.

[16]Dohmann F, Hartl C. Hydroforminga method to manufacture lightweight parts[J]. Journal of Materials Processing Technology, 1996, 60(1-4): 669-676.

[17]Nikhare C. Effect of prestrain on formability and forming limit strains during tube hydroforming[J]. Computers, Materials and Continua, 2008, 7(3): 129-138.

[18]Gao L, Mostch S, Strano M. Classification and analysis of tube hydroforming processes with respect to adaptive FEM simulations[J]. Journal of Materials Processing Technology, 2002, 129(1-3): 261-267.

[19]Ko M. Hydroforming for Advanced Manufacturing [M]. Cambridge: Woodhead Publishing, 2008.

[20]Rimkus W, Bauer H, Mihsein M J A. Design of loadcurves for hydroforming applications[J]. Journal of Materials Processing Technology, 2000, 108(1): 97-105.

[21]郎利辉，张弛，孔德帅，等. 异形截面管充液成形工艺及过程优化[J]. 锻压技术，2017，42(10):57-61.

Lang L H, Zhang C, Kong D S, et al. Optimization on hydroforming technology and process of irregular crosssection tube[J]. Forging & Stamping Technology, 2017, 42(10): 57-61.

[22]Hama T, Ohkubo T, Kurisu K, et al. Formability of tube hydroforming under various loading path[J]. Journal of Materials processing Technology, 2006, 177(1-3): 676-677.

服务与反馈：

【文章下载】【加入收藏】