网站首页期刊简介编委会过刊目录投稿指南广告合作征订与发行联系我们English
弯曲预成形和液压成形对汽车装饰尾管壁厚分布的影响
英文标题:Effect of prebending and hydroforming on thickness distribution for automobile decorative tailpipe
作者:李明 徐勇 张士宏 夏亮亮 任纯磊 陆翰 李经明 李博 
单位:中国科学院金属研究所 中国科学技术大学 苏州事达同泰汽车零部件有限公司 河南孟电集团兴迪锻压设备制造有限公司 
关键词:管材弯曲 液压成形 脉动加载 壁厚分布 装饰尾管 
分类号:TG394
出版年,卷(期):页码:2020,45(3):41-46
摘要:

针对某乘用车排气管路中的薄壁装饰尾管的整体制造难题,开展AISI 304不锈钢管材的弯曲预成形及液压成形工艺研究,从而进一步提高该产品的成形质量与成形效率。利用Dynaform软件,首先,研究弯曲预成形工艺对管材壁厚分布的影响规律,再基于此结果,完成在不同加载方式下的管材液压成形分析。结果表明:弯管Δd值较小时,管材第2次弯曲区域的减薄率有降低的趋势,并且随着Δd值的减小,这种趋势更加明显;基于所选定的Δd值,进行了液压成形有限元模拟,相比于线性加载方式,脉动加载使成品件易破裂区域的最大减薄率由17.6%降为12.1%,并且壁厚分布更为均匀;模拟与实验结果基本保持一致,最大偏差值为2.17%,成形出的零件无开裂倾向,且外观尺寸满足要求。
 

For the overall manufacturing difficulty of the thin-walled decorative tailpipe in the exhaust pipe of a passenger car, the pre-bending and hydroforming processes of AISI 304 stainless steel tube were carried out to further improve the forming quality and efficiency of product. By software Dynaform, the influence of pre-bending process on the distribution of wall thickness for tube was studied, and the hydroforming under different loading modes was analyzed based on the above result. The results show that the thinning rate of the second bending region for tube has a tendency to decrease when the value of Δd for bent tube is small, and the trend is more obvious as the value of Δd decreases. Based on selected value of Δd, the finite element simulation for hydroforming is carried out. Compared with linear loading mode, pulsating loading reduces the maximum thinning rate from 17.6% to 12.1% in the vulnerable region, and the distribution of wall thickness is more uniform. The simulation and experimental results are basically consistent, and the maximum deviation is 2.17%. Thus, there is no defect for the final part whose appearance and size meet the requirements.

基金项目:
国家自然科学基金资助项目(51875548)
作者简介:
李明(1996-),男,硕士研究生 E-mail:mli18s@imr.ac.cn 通讯作者:徐勇(1983-),男,博士,副研究员 E-mail: yongxuyy@163.com
参考文献:




[1]夏益新,王娜,陈新平,等. 热冲压和液压成形技术在宝钢汽车轻量化服务中的应用及发展趋势
[J]. 精密成形工程,2017,9(6):104-110.


Xia Y X,Wang N,Chen X P,et al. Application and development trend of lightweight technology for vehicle with hot stamping and hydroforming in baosteel
[J]. Netshape Forming Engineering,2017,9(6): 104-110.



[2]苑世剑,何祝斌,刘钢,等. 内高压成形理论与技术的新进展
[J]. 中国有色金属学报,2011,21(10): 2523-2533.


Yuan S J,He Z B,Liu G,et al. New developments in theory and processes of internal high pressure forming
[J]. The Chinese Journal of Nonferrous Metals,2011,21(10): 2523-2533.



[3]徐勇,张士宏,马彦,等. 新型液压成形技术的研究进展
[J]. 精密成形工程,2016,8(5): 7-14.


Xu Y,Zhang S H,Ma Y,et al. Hydroforming technology: Stateofthearts and recent developments
[J]. Netshape Forming Engineering,2016,8(5): 7-14.



[4]古涛,鄂大辛,任颖,等.管材弯曲壁厚变形的有限元模拟与试验分析
[J]. 模具工业,2006,(4): 17-20.


Gu T,E D X,Ren Y,et al. Finite element simulation and ex-perimental analysis of wall thickness deformation in the process of pipe bending
[J]. Die & Mould Industry,2006,(4): 17-20.



[5]张伟玮,韩聪,谢文才,等. 管材弯曲回弹对内高压成形的影响及补偿方法
[J]. 哈尔滨工业大学学报,2014,46(7): 36-39.


Zhang W W,Han C,Xie W C,et al. The effect of springback of CNC bending on hydroformed subframe and compensation methods
[J]. Journal of Harbin Institute of Technology,2014,46(7): 36-39.



[6]Ma Y,Xu Y,Zhang S,et al. The effect of tube bending,heat treatment and loading paths on process responses of hydroforming for automobile intercooler pipe:Numerical and experimental investigations
[J]. The International Journal of Advanced Manufacturing Technology,2017,91(5-8): 2369-2381.



[7]Gao L,Strano M. FEM analysis of tube prebending and hydroforming
[J]. Journal of Materials Processing Technology,2004,151(1-3): 294-297.



[8]Yuan S,Wang X,Liu G,et al. Control and use of wrinkles in tube hydroforming
[J]. Journal of Materials Processing Technology,2007,182(1-3): 6-11.



[9]Hama T,Ohkubo T,Kurisu K,et al. Formability of tube hydroforming under various loading paths
[J]. Journal of Materials Processing Technology,2006,177(1-3): 676-679.



[10]Heo S C,Kim J,Kang B S. Investigation on determination of loading path to enhance formability in tube hydroforming process using APDL
[J]. Journal of Materials Processing Technology,2006,177(1-3): 653-657.



[11]Mori K,Maeno T,Maki S. Mechanism of improvement of formability in pulsating hydroforming of tubes
[J]. International Journal of Machine Tools and Manufacture,2007,47(6): 978-984.



[12]Maeno T,Mori K,Hori A. Application of load pulsation using servo press to plate forging of stainless steel parts
[J]. Journal of Materials Processing Technology,2014,214(7): 1379-1387.



[13]Xu Y,Zhang S H,Cheng M,et al. Formability improvement of austenitic stainless steel by pulsating hydroforming
[J]. Proceedings of the Institution of Mechanical Engineers,Part B: Journal of Engineering Manufacture,2015,229(4): 609-615.



[14]Xu Y,Zhang S,Cheng M,et al. Application of pulsating hydroforming in manufacture of engine cradle of austenitic stainless steel
[J]. Procedia Engineering,2014,81: 2205-2210.



[15]Zhang S H,Yuan A Y,Wang B,et al. Influence of loading path on formability of 304 stainless steel tubes
[J]. Science in China Series E: Technological Sciences,2009,52(8): 2263-2268.



[16]Xu Y,Zhang S H,Cheng M,et al. In situ Xray diffraction study of martensitic transformation in austenitic stainless steel during cyclic tensile loading and unloading
[J]. Scripta Materialia,2012,67(9): 771-774.



[17]Xu Y,Zhang S H,Song H W,et al. The enhancement of transformation induced plasticity effect on austenitic stainless steels by cyclic tensile loading and unloading
[J]. Materials Letters,2011,65(11):1545-1547.

服务与反馈:
本网站尚未开通全文下载服务】【加入收藏
《锻压技术》编辑部版权所有

中国机械工业联合会主管 北京机电研究所有限公司 中国机械工程学会塑性工程分会主办
联系地址:北京市海淀区学清路18号 邮编:100083
电话:+86-010-82415085 传真:+86-010-62920652
E-mail: fst@263.net(稿件) dyjsjournal@163.com(广告)
京ICP备07007000号-9