锻压技术

某铝合金汽车发动机罩外板冲压成形工艺

英文标题：Stamping process of automobile engine outer panel for aluminum alloy

作者：余万铨胡志力杨冰胡文治华林

单位：武汉理工大学

分类号：TG386.3

出版年,卷(期):页码：2020,45(4):45-50

摘要：

针对铝合金材料弹性模量小、在室温条件下的冲压成形性能较差的问题,以铝合金汽车发动机罩外板为例，基于Autoform软件平台分析其冲压成形过程，通过优化型面结构改进零件的成形质量，研究了冲压工艺参数对零件减薄率和回弹的影响规律。结果表明：当采用小的压边力时，板料的减薄较小；在一定范围内，随着压边力的增大，零件的回弹有所减小。最终通过对模具进行型面补偿并结合适当的工艺参数调整，有效地减小了零件回弹。基于结果进行了发动机罩外板的冲压试验，通过模具调试使制件达到生产要求。

Due to the small elastic modulus of aluminum alloy materials and the poor forming properties of stamping at room temperature, for aluminum alloy automobile engine outer panel, its stamping process was analyzed by software Autoform, and the influences of stamping process parameters on the thinning rate and springback of parts were studied by optimizing the profile structure to improve forming quality of part. The results show that when the smaller blank holder force is applied, the thinning of sheet is smaller. However, within a certain range, the springback of part is reduced with the increasing of blank holder force. Finally, through the profile compensation of mold and the adjustment of process parameters, the springback of part is reduced efficiently. Based on the above results, a stamping test of engine outer panel was conducted. And the parts meet the production requirements by mold debugging.

基金项目：

中国汽车产业创新发展联合基金（U1564202）；国家自然科学基金资助项目（51775397）；高等学校学科创新引智计划（B17034）；教育部创新团队发展计划（IRT13087）

余万铨（1995-），男，硕士研究生 E-mail：ywq1397@163.com 通讯作者：胡志力（1983-），男，博士，副教授 E-mail:zhilihuhit@163.com

参考文献：

[1]丁海涛.基于Autoform仿真模拟的某车型后地板材料优化[J].汽车实用术,2018,(19):241-243.

Ding H T. Material optimization of rear floor of a type of vehicle based on Autoform simulation [J].Automobile Applied Technology, 2018, (19):241-243.

[2]邹伟,张立强,谭知理,等.超高强度钢热冲压实验研究[J].锻压技术,2018,43(9):174-177, 183.

Zou W, Zhang L Q,Tan Z L,et al. Experimental investigation on hot stamping for ultra-high strength steel[J].Forging & Stamping Technology, 2018,43 (9):174-177,183.

[3]崔振祥,杨丹.超高强钢前纵梁零件冲压开裂分析与处理[J].精密成形工程,2017,9(6):32-36.

Cui Z X, Yang D. Analysis and treatment of stamping cracking of front longitudinal beam parts of ultra high strength steel[J]. Journal of Netshape Forming Engineering, 2017, 9(6): 32-36.

[4]李昊,王强.基于ANSYS/LS-DYNA的工程车辆轮辐冲压工艺优化[J]. 精密成形工程, 2017, 9(3):34-39.

Li H, Wang Q. Optimization of the stamping process of engineering vehicles based on ANSYS/LS-DYNA[J]. Journal of Netshape Forming Engineering, 2017, 9(3): 34-39.

[5]谭植文,谭文娟,王占全,等.某汽车翼子板模具工艺设计[J].重庆理工大学学报:自然科学, 2018, 32(9):35-41.

Tan Z W, Tan W J, Wang Z Q, et al. Process design of a car fender mold[J]. Journal of Chongqing University of Technology: Natural Science, 2018, 32(9): 35-41.

[6]周杰,程丹,阳德森,等.汽车后轮罩板冲压工艺方案的改进[J].汽车工程,2008, (7):635-638.

Zhou J, Cheng D, Yang D S, et al. Improvement of stamping process scheme for automobile rear wheel cover plate[J]. Automotive Engineering, 2008, (7): 635-638.

[7]王晋炜,郭水军,杨旭静,等.冲压成形中凹模入口角曲线优化[J].中国机械工程, 2014, 25(24): 3333-3337.

Wang J X, Guo S J, Yang X J, et al. Optimization of entrance angle curve of concave die in stamping forming[J].China Mechanical Engineering, 2014, 25(24):3333-3337.

[8]朱超,王雷刚,黄瑶.基于CAE和灰色关联的汽车前门外板冲压成形工艺参数多目标优化[J].锻压技术,2018,43(8):39-43，70.

Zhu C, Wang L G, Huang Y. Multi-objective optimization of stamping process parameters of automobile front door outer panel based on CAE and grey correlation[J]. Forging & Stamping Technology, 2018, 43(8): 39-43,70.

[9]郭驿,熊丹丹,赵坤民.拉延筋对板料成形及回弹影响的数值模拟[J].合肥工业大学学报:自然科学版,2018,41(11):1456-1460.

Guo Y, Xiong D D, Zhao K M. Numerical simulation of the effect of drawbead on sheet forming and springback[J]. Journal of Hefei University of Technology: Natural Science, 2018, 41(11): 1456-1460.

[10]张亚岐,胡文治,穆传坤,等.非匀速冲压对厚板回弹的影响[J].汽车工程, 2017, 39(12): 1472-1476.

Zhang Y Q, Hu W Z, Mu C K,et al. The effect of non-uniform stamping on the rebound of thick plates [J].Automotive Engineering, 2017, 39(12): 1472-1476.

[11]吕少文,石光林,程金海,等.高强钢B柱的拉延回弹分析与补偿研究[J].装备制造技术, 2018, (8):130-132.

Lyu S W, Shi G L, Cheng J H, et al. Research on the analysis and compensation of the drawing rebound of high-strength steel B-pillar[J]. Equipment Manufacturing Technology, 2018, (8):130-132.

[12]李延平,朱东波,卢秉恒.基于RP/RT/RE技术的金属板料冲压成形回弹误差补偿系统[J].中国机械工程,2005,(7):636-640.

Li Y P, Zhu D B, Lu B H. Springback error compensation system for metal sheet stamping based on RP/RT/RE technology[J]. China Mechanical Engineering, 2005,(7): 636-640.

服务与反馈：

【本网站尚未开通全文下载服务】【加入收藏】