锻压技术

5A06铝合金端板构件成形工艺优化

英文标题：Optimization on forming process of 5A06 aluminum alloy end-plate

作者：田鹏刘宝胜陈福龙吴为

分类号：V261.2+8

出版年,卷(期):页码：2020,45(4):76-86

摘要：

所研究的铝合金端板构件为端部异向翻折零件，成形过程中局部极易产生起皱和破裂等缺陷。针对端板构件成形过程中存在的起皱及成形精度差等问题，通过对模具结构进行优化设计，实现了单道次整体成形，提高了产品的整体性及成形质量；同时，通过有限元模拟分析，选取合理的坯料形状，解决了零件成形过程中的开裂问题，并进行了试验验证。结果表明：与无顶板的传统凸、凹模结构相比，采用带凹模顶板的优化结构时，端板构件过渡区域起皱现象得到有效缓解，最大增厚率减少至6.7%；采用过渡圆角为R50 mm的凸耳结构坯料时，端板构件过渡区域最大减薄率减少至12.11%。

The aluminum alloy end-plate researched was a kind of typical part accompanied by end flange folding in the reverse direction, and defects such as winkles and cracks were extremely prone to occur during the forming process. According to the problems of wrinkles and poor forming accuracy in the forming process of end-plate, the mold structure was optimized to realize single-pass forming and improve the integrity and forming quality of products. Meanwhile, the appropriate blank shape was selected by the finite element analysis, which could eliminate the cracking problem during the forming process of products, and it was verified by test. The results show that compared to the traditional punch and die structure without die roof, the wrinkling of transition area in end-plate is effectively relieved by the optimized structure with die roof, and the maximum thickening rate is reduced to 6.7%. And the maximum thinning rate of transition area in end-plate was controlled to be 12.11% by adopting the blank with lug structure of R50 mm.

基金项目：

田鹏（1988-），男，硕士，工程师 E-mail：buaatianpeng@163.com

参考文献：

[1]孙梦莹,毕宝鹏.5A06铝合金板材超塑气胀成形壁厚均匀性研究及模具设计[J].热加工工艺,2016,45(11):132-135.

Sun M Y, Bi B P. Research on thickness uniformity of 5A06 aluminum alloy sheet superplastic gas bluging forming and its die design [J]. Hot Working Technology, 2016,45(11): 132-135.

[2]高辉,刘波,李小曼,等.5A06铝合金T型变管径半管冷冲压成形工艺[J].锻压技术,2019,44(3):36-40.

Gao H, Liu B, Li X M, et al. Cold stamping process of 5A06 aluminum alloy T-shaped semi-pipe with variable diameter[J]. Forging & Stamping Technology, 2019,44(3):36-40.

[3]孙志莹,郎利辉,孔德帅.铝合金马鞍形件充液成形工艺模拟分析[J].精密成形工程,2015,7(1):46-50，65.

Sun Z Y, Lang L H, Kong D S. Simulation analysis of hydroforming process for aluminum alloy saddle parts [J]. Journal of Netshape Forming Engineering, 2015,7(1):46-50,65.

[4]丁少行,郎利辉,黄磊.2024铝合金难成形高锥盒形件充液成形数值模拟[J].精密成形工程,2014,6(3):31-35, 40.

Ding S H, Lang L H, Huang L. Simulation research on hydroforming of hard forming deep taper-shaped part of 2024 aluminum alloy[J]. Journal of Netshape Forming Engineering, 2014,6(3):31-35, 40.

[5]郝花蕾,吉卫,江学强,等.5A06铝合金壳体拉深及翻边成形研究[J].塑性工程学报,2019,26(5):78-85.

Hao H L, Ji W, Jiang X Q, et al. Investigation on deep-drawing and flanging of 5A06 aluminum alloy shell[J]. Journal of Plasticity Engineering, 2019,26(5):78-85.

[6]陆宏,黄文,刘庆国,等.铝合金筒形件充液拉深成形过程中模具参数对回弹的影响[J].锻压技术,2019,44(10):24-28.

Lu H, Huang W, Liu Q G, et al. Influence of die parameters on springback during hydroforming for aluminum alloy cylindrical part [J]. Forging & Stamping Technology, 2019,44(10):24-28.

[7]冯苏乐,李林才,罗益民,等.大直径铝合金双曲率薄壁件拉深成形技术[J].上海航天,2019,36(2):104-110.

Feng S L, Li L C, Luo Y M, et al. Deep drawing technology for large diameter double curvature aluminum alloy thin-walled part [J]. Aerospace Shanghai, 2019,36(2):104-110.

[8]邰清安,李治华,孙立群,等.航空发动机塑性成形技术的应用与展望[J].航空制造技术,2014,(7):34-39

Tai Q A, Li Z H, Sun L Q, et al. Application and prospect of aeroengine plastic forming technology [J]. Aeronautical Manufacturing Technology, 2014,(7):34-39.

[9]杨中玉,张津,郭学博,等.铝合金的织构及测试分析研究进展[J].精密成形工程,2013,5(6):1-6,47.

Yang Z Y, Zhang J, Guo X B, et al. Research progress on aluminum alloy texture and test analysis [J]. Journal of Netshape Forming Engineering, 2013, 5(6):1-6,47.

[10]郎利辉,巫永坤,王永铭,等.关键工艺参数对铝合金斜法兰非轴对称盒形件充液成形的影响[J].锻压技术,2018,43(6):47-52.

Lang L H, Wu Y K, Wang Y M, et al. Influence of critical process parameters on hydroforming for aluminum alloy non-axisymmetric box with oblique flange [J]. Forging & Stamping Technology, 2018,43(6):47-52.

[11]郎利辉,王永铭,谢亚苏,等.某铝合金异形盒形件充液成形坯料形状优化[J].精密成形工程,2013,5(3):19-23.

Lang L H, Wang Y M, Xie Y S, et al. The blank optimization of aluminum alloy irregular box sheet hydroforming process [J]. Journal of Netshape Forming Engineering, 2013,5(3):19-23.

[12]吴建军,郭军.钣金零件毛坯展开计算方法研究进展[J].航空制造技术,2011,(19):26-31.

Wu J J, Guo J. Research development of sheet metal part spreading method [J].Aeronautical Manufacturing Technology, 2011,(19):26-31.

[13]唐炳涛,赵震,陈军,等. 冲压件坯料的优化设计方法研究[J].塑性工程学报,2004,11(6):7-11.

Tang B T, Zhao Z, Chen J, et al. The study of blank optimization methods for stamping parts[J]. Journal of Plasticity Engineering, 2004,11(6):7-11.

服务与反馈：

【文章下载】【加入收藏】