锻压技术

基于灰色关联度的筒形件二道次强力旋压工艺参数优化

英文标题：Optimization on two-pass power spinning process parameters for cylindrical parts based on grey correlation degree

作者：郭佩剑樊文欣李志伟张厚祖郝晓华

单位：中北大学

分类号：TG306

出版年,卷(期):页码：2020,45(4):108-113

摘要：

为使锡青铜筒形件具有更高的尺寸精度，对二道次强力旋压加工工艺参数进行优化。减薄率、道次分配比、第1道次进给比和第2道次进给比为主要影响筒形件成形质量的工艺参数，以筒形件的内径扩径量和壁厚偏差为优化目标。采用正交试验和灰色关联度分析法对Simufact仿真模拟软件得到的二道次仿真结果进行工艺参数优化，结果表明：各工艺参数对筒形件成形质量的影响程度依次为：减薄率＞道次分配比＞第1道次进给比＞第2道次进给比。优化后的工艺参数组合为：减薄率为40%、道次分配比为5∶5、第1道次进给比为0.6 mm·r-1、第2道次进给比为0.6 mm·r-1，所获的筒形件尺寸精度最优。

In order to make the cylindrical parts of tin bronze have higher dimensional accuracy, the process parameters of two-pass power spinning were optimized. The thinning rate, the distribution ratio of passes, the feeding ratio of the first pass and the feeding ratio of the second pass were the main process parameters that affected the forming quality of cylindrical parts. Taking the inner diameter expansion and the wall thickness deviation of cylindrical part as the optimization objective. Orthogonal experiment and grey correlation degree analysis method were used to optimize the process parameters of two-pass simulation results obtained by simulation software Simufact. The results show that the influence degree of each process parameter on the forming quality of cylindrical parts is as follows: thinning rate>distribution ratio of passes＞ feeding ratio of the first pass >feeding ratio of the second pass. The optimized combination of process parameters is as follows: the thinning rate is 40%, the pass distribution ratio is 5∶5, the feeding ratio of the first pass is 0.6 mm·r-1, the feeding ratio of the second pass is 0.6 mm·r-1, and the dimensional accuracy of the obtained cylindrical part is the best.

基金项目：

山西省自然科学基金资助项目(2012011023-2)；山西省科技攻关项目(20120321035-04)

郭佩剑(1994-)，男，硕士研究生 E-mail：511826022@qq.com 通讯作者：樊文欣(1964-)，男，博士，教授 E-mail：fanwx@nuc.edu.cn

参考文献：

[1]张涛. 旋压成形工艺[M].北京：化学工业出版社，2009.

Zhang T. Spin Forming Process [M]. Beijing: Chemical Industry Press, 2009.

[2]王成和，旋压技术[M].福州：福建科学技术出版社，2017.

Wang C H. Spinning Technology [M]. Fuzhou: Fujian Science and Technology Press, 2017.

[3]Essa K, Hartley P. Numerical simulation of single and dual pass conventional spinning processes[J]. International Journal of Material Forming, 2009, 2(4):271-281.

[4]Essa K, Hartley P.Optimization of conventional spinning process parameters by means of numerical simulation and statistical analysis[J].Proceedings of the Institution of Mechanical Engineers，Part B: Engineering Manufacture,2010,224(11):1691-1705.

[5]刘双耀. 多道次无芯模旋压成形方式及其优化研究[D].杭州：浙江大学,2017.

Liu S Y. Multi-pass Coreless Die Spinning Forming Method and Its Optimization[D]. Hangzhou: Zhejiang University, 2017.

[6]刘翀. 铸造铝合金筒形件多道次强力热反旋椭圆度研究[D]. 南昌:南昌航空大学,2015.

Liu C. Study on Multi-pass Strong Thermal Reverse Ellipticity of Cast Aluminum Alloy Tubular Parts [D]. Nanchang: Nanchang Aeronautical University,2015.

[7]金贺荣,张磊.多道次热轧不锈钢复合板热力耦合模拟及试验研究[J].塑性工程学报,2018,25(5):158-165.

Jin H R, Zhang L. Thermo-mechanical coupling simulation and experimental study of multi-pass hot-rolled stainless steel clad plates[J]. Journal of Plasticity Engineering，2018,25(5):158-165.

[8]郝唯岑. 锡青铜（QSn7-0.2）连杆衬套多道次旋压成形工艺研究[D].太原：中北大学,2018.

Hao W C. Research on Multi-pass Spin Forming Process of Tin Bronze (QSn7-0.2) Connecting Rod Bushing [D].Taiyuan: North University of China, 2018.

[9]杨锋,樊文欣,汤传尧,等.基于Simufact筒形件强力旋压与变薄拉深成形质量研究[J].锻压技术,2018,43(2):49-54.

Yang F, Fan W X, Tang C Y, et al. Study on the quality of spinning and thinning deep drawing based on Simufact cylindrical parts[J]. Forging & Stamping Technology, 2018,43(2):49-54.

[10]平欣, 平鹏. 圆度、同轴度和圆柱度误差的最小二乘评定法[J].中国测试, 1997,(2):44-45.

Ping X, Ping P. Least squares evaluation method for roundness, concentricity and cylindricity error[J]. China Testing, 1997,(2): 44-45.

[11]刘继林,汤传尧,樊文欣.旋轮参数对反旋管型件成形质量的影响[J].锻压技术,2019,44(5):82-85,92.

Liu J L, Tang C Y, Fan W X. Influence of spinner parameters on forming quality of anti-rotor tubes[J]. Forging & Stamping Technology, 2019,44(5):82-85,92.

[12]席奇豪，樊文欣,吕伟.基于灰色关联度的强力旋压成形工艺参数优化[J].热加工工艺,2016,45(15):129-132.

Xi Q H, Fan W X, Lyu W. Optimization of process parameters for strong spinning process based on grey correlation degree[J]. Hot Working Technology,2016,45(15):129-132.

服务与反馈：

【文章下载】【加入收藏】