锻压技术

Mg-8Gd-1Er-0.5Zr合金多向锻造工艺及锻后组织与力学性能研究

英文标题：Research on multi-directional forging process and microstructure and mechanical properties after forging for Mg-8Gd-1Er-0.5Zr alloy

作者：丁宁杜文博付金龙郭成龙李硕朱训明

单位：北京工业大学万丰奥特控股集团有限公司

关键词：Mg-8Gd-1Er-0.5Zr合金等温多向锻造锻造温度累积应变量微观组织力学性能

分类号：TG316.2

出版年,卷(期):页码：2020,45(5):1-5

摘要：

为改善和提高Mg-8Gd-1Er-0.5Zr合金的组织和力学性能，采用不同锻造温度和累积应变量对Mg-8Gd-1Er-0.5Zr合金进行了等温多向锻造实验，并测试和分析了合金的组织和力学性能。实验结果表明：在实验温度范围内，随着锻造温度的升高，Mg-8Gd-1Er-0.5Zr合金的可锻性逐步提高；在420 ℃锻造时，锻造初期产生大量的孪晶以协调变形，随着锻造温度升高至480 ℃，孪晶数量减少，再结晶晶粒数量增加，且平均晶粒尺寸有一定的增大；在累积应变量Δε=0.66时，与420 ℃锻造时相比，450 ℃锻造后的试样强度略有降低，但伸长率明显增加，其抗拉强度、屈服强度、伸长率分别为295 MPa、252 MPa、13.8%，但当锻造温度提高到480 ℃时，强度下降；当锻造温度一定时，随着累积应变量的增加，合金内部组织经历了从原始粗晶到混晶组织、再到由再结晶晶粒组成的细小均匀组织的演变，且合金在Δε=0.66时的力学性能最佳。最终，确定了Mg-8Gd-1Er-0.5Zr合金的锻造温度优选为450 ℃。

In order to improve the microstructure and mechanical properties of Mg-8Gd-1Er-0.5Zr alloy, the isothermal multi-directional forging experiments under various forging temperatures and accumulated strains were conducted, and the microstructure and mechanical properties of alloy were tested and analyzed. The results show that the forge-ability of Mg-8Gd-1Er-0.5Zr alloy is gradually improved by increasing the forging temperature within the experimental temperature range. When the alloy is forged at 420 ℃, a large number of twins are formed in the initial stage of forging to coordinate the deformation. By increasing the forging temperature to 480 ℃, the volume fraction of twins reduces whereas the number of recrystallized grains increases, and the average grain size becomes larger. Compared with the sample forged at 420 ℃ under the accumulated strain of 0.66, the alloy forged at 450 ℃ exhibits a slight decrease in strength, but the elongation ratio increases obviously, and its tensile strength, yield strength and elongation ratio are 295 MPa、252 MPa and 13.8%, respectively. However, the strength decreases when the alloy is forged at 480 ℃. Furthermore, when the forging temperature is constant, with the increasing of the accumulated strain, the internal structure of alloy evolves from the original coarse grains to the mixed crystal structure, and then to the fine uniform structure composed of recrystallized grains. In addition, the alloy has the best mechanical properties under the accumulated strain of 0.66, and the optimal forging temperature of Mg-8Gd-1Er-0.5Zr alloy is preferably 450 ℃.

基金项目：

国家重点研发计划（2016YFB0301101）；浙江省领军型创新创业团队项目（201602007）

丁宁（1995-），男，硕士研究生，E-mail：s201709121@emails.bjut.edu.cn；通讯作者：杜文博（1964-），男，博士，教授，E-mail：duwb@bjut.edu.cn

参考文献：

[1]丁文江. 镁合金科学与技术 [M].北京：科学出版社，2007.
Ding W J. Science and Technology for Magnesium Alloy[M]. Beijing: Science Press, 2007.
[2]孙艳芬,赵清军.锻压态AZ81镁合金的组织与性能 [J].锻压技术,2018,43(10):43-46,51.
Sun Y F, Zhao Q J. Microstructure and properties of forging state AZ81 magnesium alloy [J]. Forging & Stamping Technology, 2018, 43(10): 43-46,51.
[3]Chen C, Song L H, Du X H, et al. Enhanced mechanical property of AZ31B magnesium alloy processed by multidirectional forging method [J]. Materials Characterization, 2017, 131: 72-77.
[4]Wu D, Chen R S, Tang W N, et al. Influence of texture and grain size on the roomtemperature ductility and tensile behavior in a MgGdZn alloy processed by rolling and forging [J]. Materials & Design, 2012, 41: 306-313.
[5]Hong M, Wu D, Chen R S, et al. Ductility enhancement of EW75 alloy by multidirectional forging [J]. Journal of Magnesium and Alloys, 2014, 2(4): 317-324.
[6]Liu B, Zhang Z, Jin L, et al. Forgeability, microstructure and mechanical properties of a freeforged Mg-8Gd-3Y-0.4Zr alloy [J]. Materials Science and Engineering A, 2016, 650: 233-239.
[7]Merson D, Vasiliev E, Markushev M, et al. On the corrosion of ZK60 magnesium alloy after severe plastic deformation [J]. Letters on Materials, 2017, 7(4): 421-427.
[8]刘金辉,宋影伟,单大勇,等.铸态和锻造态Mg-5Y-7Gd-1Nd-0.5Zr合金腐蚀行为对比研究 [J].金属学报, 2018, 54(8): 1141-1149.
Liu J H, Song Y W, Shan D Y, et al. Comparative study on corrosion behavior of cast and forged Mg-5Y-7Gd-1Nd-0.5Zr alloys [J]. Acta Metallurgica Sinica, 2018, 54(8): 1141-1149.
[9]郝孟军,宫涛,代艳霞.汽车轮毂用改性镁合金锻造工艺 [J]. 锻压技术, 2019, 44(4): 22-27.
Hao M J, Gong T, Dai Y X. Modified magnesium alloy forging process for automobile hub [J]. Forging & Stamping Technology, 2019, 44(4): 22-27.
[10]梁晓亮.锻造温度对汽车用镁合金组织和性能的影响 [J].锻压技术, 2018, 43(9): 169-174.
Liang X L. Influence of forging temperature on microstructure and properties of automotive magnesium alloy [J]. Forging & Stamping Technology, 2018, 43(9): 169-174.
[11]潘吉鹏. 高强MgGdY-ZnZr合金锻造变形和组织性能研究 [D]. 哈尔滨:哈尔滨工业大学, 2013.
Pan J P. The Forging Behavior of Highstrength MgGdY-ZnZr Alloy [D]. Harbin: Harbin Institute of Technology, 2013.
[12]SalandariRabori A, ZareiHanzaki A, Abedi H R, et al. Micro and macro texture evolution during multiaxial forging of a WE43 magnesium alloy [J]. Journal of Alloys and Compounds, 2018, 739: 249-259.
[13]Tang L, Liu C, Chen Z, et al. Microstructures and tensile properties of MgGdY-Zr alloy during multidirectional forging at 773K [J]. Materials & Design, 2013, 50: 587-596.
[14]Zheng X B, Du W B, Wang Z H, et al. Remarkably enhanced mechanical properties of Mg-8Gd-1Er-0.5Zr alloy on the route of extrusion, rolling and aging [J]. Materials Letters, 2018, 212: 155-158.

服务与反馈：

【文章下载】【加入收藏】