锻压技术

翼子板冲压工艺设计及成形分析

英文标题：Stamping process design and forming analysis on fender

作者：何磊

单位：北京奔驰汽车有限公司

分类号：TG386

出版年,卷(期):页码：2020,45(5):115-121

摘要：

通过CAE仿真分析软件，对翼子板进行CAE成形分析，将大量CAE分析数据和实际工艺设计经验相结合，总结归纳出翼子板冲压工艺方案设计要素及注意事项。阐述了翼子板合件和单件工艺方案的各自优缺点，详细总结了拉延工序中冲压方向、压料面和工艺补充的作用、设计方法和基本要求，同时也介绍了后工序工艺内容、各自特点以及注意事项。此外，对设计中易出现的工艺问题给出了经CAE分析和实际生产同时验证后的可行性解决方案，并介绍了为了改善冲压工艺性对零件局部特征进行优化的方法。经生产验证，提出的设计方案工艺性合理、产品质量稳定，能够满足大量生产需求。

The forming process of fender was analyzed by simulation analysis software CAE, and the key elements and considerations in the design of stamping process plan for fender were summarized by combining a lot of CAE analysis data with practical process design experiences. Then, the advantages and disadvantages of process plans for both double and single parts were described respectively, and the functions, design method and basic requirements of stamping direction, blank holder surface and process supplement in the drawing process, as well as the contents, their respective characteristics and the considerations of the later processes were introduced emphatically. In addition, the feasible solutions to the process problems which were easy to appear in the design were given which were verified by CAE analysis and practical production, and the method of optimizing the local characteristics of parts was introduced to improve the stamping processability. After the verification of production, the design plan proposed is reasonable in processability and stable in product quality, and meets the needs of large-scale production.

基金项目：

何磊（1988-），男，学士，工程师，E-mail：heleicumt@163.com

参考文献：

[1]吴志兵，杨建，吴雄伟，等. 车身外造型关键区域分缝研究 [J].锻压技术，2019,44(10):56-63.
Wu Z B，Yang J，Wu X W，et al. Research on key area parting for car body exterior [J]. Forging & Stamping Technology，2019,44(10):56-63.
[2]胡殿柱. 翼子板典型缺陷分析及改进方案 [J].模具制造，2019,19(10):1-4
Hu D Z. Typical defects analysis and improvement scheme of wing plate [J]. Die & Mould Manufacture，2019,19(10):1-4
[3]程瑞贺，赵烨，孙小会，等.翼子板浅拉延工艺的应用研究 [J].汽车工艺与材料，2019,(1):26-29.
Cheng R H，Zhao Y，Sun X H，et al. Applied research on shallow drawing of fender [J]. Automobile Technology & Material，2019,(1):26-29.
[4]李贵，崔赛赛，梁中凯，等. 汽车覆盖件旋转斜楔冲压工艺优化设计 [J]. 锻压技术，2018,43(3):133-139.
Li G，Cui S S，Liang Z K，et al. Optimization design on stamping process of rotational wedge for automotive panels [J].Forging & Stamping Technology，2018,43(3):133-139.
[5]金磊，王宝川，韩龙帅，等. 基于AutoForm的材料仿真数据影响因素研究 [J]. 锻压技术，2019,44(9):180-186.
Jin L，Wang B C，Han L S，et al. Research on influencing factors of material simulation data based on AutoForm[J]. Forging & Stamping Technology，2019,44(9):180-186.
[6]邓璐璐，林建平，侯勇，等. 轿车覆盖件表面畸变的影响因素及规律研究 [J]. 锻压技术，2018,43(8):58-64.
Deng L L，Lin J P，Hou Y，et al. Study on influence factors and regularity of surface distortion for automobile exterior panels[J]. Forging & Stamping Technology，2018,43(8):58-64.
[7]左治江，张宇辉，丁元才. 基于AutoForm的汽车顶盖拉延工艺分析及模具设计 [J]. 锻压技术，2019,44(3):101-106.
Zuo Z J，Zhang Y H，Ding Y C. Drawing process analysis and die design of automobile roof cover based on AutoForm[J]. Forging & Stamping Technology，2019, 44(3):101-106.
[8]王海玲，崔礼春，陈世涛. 某汽车尾门内板冲压工艺方案及拉深成形模设计 [J]. 锻压技术，2018,43(9):55-61.
Wang H L，Cui L C，Chen S T. Stamping process and drawing die design for car tail-gate inner panel [J]. Forging & Stamping Technology，2018, 43(9):55-61.
[9]宗可明. 典型汽车覆盖件工艺补充面设计方法研究 [J] .佳木斯职业学院学报，2016，（10）:497-498.
Zong K M. Research on the design method of typical automobile panel technology [J]. Journal of Juamjusi Education Institute，2016，（10）:497-498.
[10]胡平. 基于扫描面的汽车覆盖件工艺补充设计 [J]. 机械工程学报，2006，42(1):117-120.
Hu P. Design of auto-body panel addendum based on sweep surface [J]. Chinese Journal of Mechanical Engineering，2006，42 (1):117-120.
[11]段彦宾，王冀军. 汽车覆盖件压料面设计与分析 [J]. 模具制造，2018，18(12): 29-32.
Duan Y B，Wang J J. Research on the design and analysis for the binder surface in automobile panel [J]. Die & Mould Manufacture，2018，18(12): 29-32.
[12]洪国华. 基于AutoForm的汽车门内板轮弧面起皱的优化 [J]. 锻压技术，2018,43(8):71-74.
Hong G H. Optimization on arc surface wrinkle for automobile rear door inner panel based on AutoForm [J]. Forging & Stamping Technology，2018,43(8):71-74.

服务与反馈：

【文章下载】【加入收藏】