锻压技术

准β锻造工艺对TC21钛合金大型锻件组织及性能的影响

英文标题：Influence of quasi-β forging process on microstructure and properties of TC21 titanium alloy large forgings

作者：周晓虎刘卫郝芳毛友川赖运金赵张龙

单位：西安三角防务股份有限公司西部超导材料科技股份有限公司西北工业大学西安欧中材料科技有限公司

分类号：TG113.25

出版年,卷(期):页码：2020,45(6):29-34

摘要：

以TC21钛合金特大规格棒材及其制备的大型锻件为研究对象，采用准β锻造工艺锻造TC21钛合金，分析了3种不同锻造方案对锻件微观组织和力学性能的影响规律。结果表明：TC21钛合金可在相变点以上一定温度采用准β锻造工艺加工，在不同的加热工艺参数下，通过双重退火进行热处理，均可获得较好的冶金组织和力学性能。TC21钛合金在准β锻造过程中，不同的锻造温度和锻造火次均能获得较好的拉伸性能（1100 MPa左右）和断裂韧性（大于90 MPa·m1/2）。在准β锻造过程中，较高的锻造温度有利于获得网篮组织，合金的断裂韧性较高，组织内片层α相存在粗化趋势；较低的准β锻造温度有利于细化微观组织，但锻造后组织中会有少量残余等轴α相存在。在锻造变形量相同的情况下，较少锻造火次可以获得更加细小的微观组织，但锻件不同部位的微观组织形态存在差异。

For the TC21 titanium alloy oversized bar and the large forgings manufactured by it, TC21 titanium alloy was forged by the quasi-β forging process, and the influence laws of three different forging plans on the microstructure and mechanical properties of forgings were analyzed. The results show that the TC21 titanium alloy obtains better metallurgical structure and mechanical properties by quasi-β forging process at a certain temperature above the phase transformation point and under different heating process parameters as well as heat treatment by double annealing. Furthermore, TC21 titanium alloy obtains better tensile performance (about 1100 MPa) and fracture toughness (greater than 90 MPa·m1/2) under different forging temperatures and forging fire times in the quasi-β forging process. In the process of quasi-β forging, the higher forging temperature is conducive to obtain the basket structure, the fracture toughness of alloy is higher, and the lamellar α phase of structure has a tendency to coarsen. However, the lower quasi-β forging temperature is conducive to the refinement of microstructure, but there is a small amount of residual equiaxed α phase in the structure after forging. Under the same amount of forging deformation, the finer microstructure is obtained by less forging fire times, but the microstructure morphologies at different positions of the forgings are different.

基金项目：

陕西省重点研发计划(2018ZDXM-GY-132)

作者简介：周晓虎（1975-），男，硕士，高级工程师 E-mail：zzhouxiaohu@126.com 通讯作者：赖运金（1979-），男，博士，教授级高级工程师 E-mail：30149395@qq.com

参考文献：

［1］赵永庆,曲恒磊,冯亮,等.高强高韧损伤容限型钛合金TC21研制
［J］.钛工业进展,2004，21(1):22-24.

Zhao Y Q，Qu H L，Feng L，et al. Research on high strength, high toughness and high damage-tolerant titanium alloy-TC21
［J］. Titanium Industry Progress，2004，21(1):22-24.

［2］闫辰侃,曲寿江,冯艾寒,等.钛及钛合金形变孪晶的研究进展
［J］.稀有金属, 2019,43(5):449-460.

Yan C K, Qu S J, Feng A H, et al. Recent advances of deformation twins in titanium and titanium alloys
［J］. Chinese Journal of Rare Metals, 2019,43(5):449-460.

［3］曲恒磊,赵永庆,冯亮,等.TC21钛合金不同变形条件下的显微组织研究
［J］.材料工程,2006，(S1):274-277.

Qu H L, Zhao Y Q, Feng L, et al. Study on microstructure of TC21 titanium alloy under different deformation conditions
［J］. Journal of Materials Engineering,2006，(S1):274-277.

［4］曹春晓.选材判据的变化与高损伤容限钛合金的发展
［J］.金属学报, 2002, 38(S1):4-11.

Cao C X. Change of material selection criterion and development of high damage-tolerant titanium alloy
［J］. Acta Metallurgica Sinica, 2002, 38(S1):4-11.

［5］雷锦文,曾卫东,朱知寿,等.TC21钛合金β锻造大块α相研究
［J］.材料热处理学报,2009,30(5):14-18.

Lei J W, Zeng W D, Zhu Z S, et al. Research on blocky alpha in beta processed TC21 titanium alloy
［J］. Transactions of Materials and Heat Treatment,2009,30(5):14-18.

［6］朱知寿,王新南,童路,等.新型TC21钛合金热处理工艺参数与显微组织演变的关系研究
［J］.钛工业进展,2006，(6):24-27.

Zhu Z S, Wang X N, Tong L, et al. Study on the relationship between heat treatment parameters and microstructures evolvement of new type TC21 titanium alloy
［J］. Titanium Industry Progress,2006，(6):24-27.

［7］周义刚,曾卫东,俞汉清.近β锻造推翻陈旧理论发展了三态组织
［J］.中国工程科学,2001，(5):61-66.

Zhou Y G, Zeng W D,Yu H Q. The near β forging overthrows the conventional forging theory and develops a new tri-modal microstructure
［J］. Engineering Science,2001，(5):61-66.

［8］毕彦，乔靖雯，马叙，等. 锻造温度对新型含铌汽车钛合金棒材性能的影响
［J］. 锻压技术，2018,43(9):14-20.

Bi Y，Qiao J W，Ma X，et al. Forging formability analysis on Cu-Cr-Zr rotor end ring of high power motor
［J］. Forging & Stamping Technology，2018,43(9):14-20.

［9］石志峰. TC21钛合金工艺优化及组织性能关系研究
［D］.西安：西北工业大学,2016.

Shi Z F. Researches on Processing Optimization and Microstructure-property Relationship of TC21 Titanium Alloy
［D］. Xi′an: Northwestern Polytechnical University,2016.

［10］赖运金. 钛合金片状组织演变机制与球化动力学研究
［D］.西安：西北工业大学,2007.

Lai Y J. Study on Microstructural Evolution of Lamellar Structure and Globularization Kinetics of Titanium Alloy
［D］. Xi′an: Northwestern Polytechnical University,2007.

［11］程新江,代洪庆.TC21合金准β锻热变形过程数值模拟及试验研究
［J］.特种铸造及有色合金,2017,37(2):136-139.

Cheng X J, Dai H Q. Simulation of quasi β forging deformation process in TC21 alloy and experiment
［J］. Special-cast and Non-ferrous Alloys,2017,37(2):136-139.

［12］王涛,万志鹏,孙宇,等.镍基变形高温合金动态软化行为与组织演变规律研究
［J］.金属学报,2018,54(1):83-92.

Wang T, Wan Z P, Sun Y, et al. Dynamic softening behavior and microstructure evolution of nickel base superalloy
［J］. Acta Metallurgica Sinica,2018,54(1):83-92.

［13］邹忠波,董洪波,朱深亮,等.三重热处理温度对TC21钛合金显微组织的影响
［J］.特种铸造及有色合金,2016,36(4):438-441.

Zou Z B,Dong H B,Zhu S L, et al. Effects of triple heat treatment temperature on microstructure of TC21 titanium alloy
［J］. Special-cast and Non-ferrous Alloys,2016,36(4):438-441.

［14］Shi Z F, Guo H Z, Zhang J W, et al. Microstructure fracture toughness relationships and toughening mechanism of TC21 titanium alloy with lamellr microstructure
［J］. Transactions of Nonferrous Metals Society of China, 2018,28(12):2440-2448.

［15］Wen X, Wan M P, Huang C W, et al. Strength and fracture toughness of TC21 alloy with multi-level lamellar microstructure
［J］. Materials Science and Engineering: A, 2019, 740-741:121-129.

［16］钦兰云,李明东,杨光,等. 热处理对激光沉积TC4钛合金组织与力学性能的影响
［J］. 稀有金属, 2018,42(7):698-704.

Qin L Y, Li M D, Yang G, et al. Microstructure and mechanical properties of laser deposition manufacturing TC4 titanium alloy with heat treatment
［J］. Chinese Journal of Rare Metals, 2018,42(7):698-704.

［17］袁士翀，王周田，高志刚，等. β锻造参数对TC17钛合金组织性能的影响
［J］. 锻压技术，2018,43(2):14-18.

Yuan S C，Wang Z T，Gao Z G，et al. Influence of β forging parameters on microstructure and properties of titanium alloy TC17
［J］. Forging & Stamping Technology，2018,43(2):14-18.

［18］李鑫. TC11钛合金的热态变形行为及其锻造工艺优化研究
［D］. 南京:南京航空航天大学, 2009.

Li X. Hot Deformation Behavior and Forging Process Optimization of TC11 Titanium Alloy
［D］. Nanjing:Nanjing University of Aeronautics and Astronautics, 2009.

［19］朱知寿.航空结构用新型高性能钛合金材料技术研究与发展
［J］.航空科学技术,2012，(1):5-9.

Zhu Z S. Recent research and development of titanium alloys for aviation uses in China
［J］. Journal of Aeronautical Materials, 2012，(1):5-9.

［20］Fei Y H, Zhou L, Qu H L, et al. The phase and microstructure of TC21 alloy
［J］. Materials Science and Engineering: A, 2008, 494(1-2):166-172.

服务与反馈：

【文章下载】【加入收藏】