锻压技术

预加热对TA1钛合金自冲铆接性能的影响

英文标题：Influence of preheating on properties of self-piercing riveting for TA1 titanium alloy

作者：黄志超肖锐刘帅红周泽杰赖家美

单位：华东交通大学南昌大学

分类号：TG386

出版年,卷(期):页码：2020,45(6):80-85

摘要：

为探究温度对TA1钛合金自冲铆接性能的影响，在预加热条件下采用钛钛TA1+TA1、钛铝TA1+5052、铝钛5052+TA1这3种组合方式进行自冲铆接试验，对所得的接头进行静态拉伸试验，观察20，100和150 ℃这3种预加热温度下的接头成形截面和拉伸失效形式。结果表明：不同板料组合下的自冲铆接接头的成形截面不同，随着预加热温度升高，成形截面的底厚逐渐降低。在同一温度下，TA1+TA1接头的静强度最高，上板拉出而失效；TA1+5052接头次之，下板产生断裂失效；5052+TA1接头最低，上板产生断裂失效。随着预加热温度的升高，3种接头的静强度明显下降，但是失效形式不发生明显的变化；在能量吸收值方面， TA1+TA1接头的能量吸收值逐渐下降，TA1+5052、5052+TA1接头的能量吸收值逐渐上升。

In order to explore the influence of temperature on the self-piercing riveting properties of TA1 titanium alloy, the self-piercing riveting test was conducted under the preheating condition by three combinations of titanium/titanium(TA1+TA1), titanium/aluminum (TA1+5052) and aluminum/titanium(5052+TA1), and the forming sections and tensile failure forms of the joints under the three preheating temperatures of 20, 100 and 150 ℃ were observed by the static tensile test on the joint. The results show that the forming sections of the self-piercing riveting joints are different under different sheet metal combinations, and the bottom thickness of the forming section decreases with the increasing of preheating temperature. At the same temperature, the static strength of TA1+TA1 joint is the highest, and the upper sheet is pulled out and fails. TA1+5052 is the second, and the lower sheet is broken. 5052+TA1 is the lowest, and the upper sheet is broken. With the increasing of preheating temperature, the static strength of the three joints decreases obviously, but the failure mode does not change significantly. However, in terms of energy absorption value, TA1+TA1 joint decreases gradually, TA1+5052 and 5052+TA1 joint increases gradually.

基金项目：

国家自然科学基金资助项目（51875201，51565014）

黄志超(1971-)，男，博士，教授 E-mail：hzcosu@163.com

参考文献：

［1］戴云鹏. 汽车轻量化中自冲铆连接技术的工艺特点
［J］.机电技术，2017，(1):61-63.

Dai Y P. Technological characteristics of self-piercing riveting connection technology in lightweight automobile
［J］. Electromechanical Technology, 2017,(1):61-63.

［2］金鑫, 李永兵,楼铭,等.基于正交试验的铝合金——高强钢异种金属自冲铆接工艺优化
［J］.汽车工程学报,2011,1(4):185-191.

Jing X,Li Y B, Lou M，et al. Optimization of self-piercing riveting process for dissimilar metals of aluminum alloy high strength steel based on orthogonal test of Shanghai automobile
［J］.Journal of Automotive Engineering,2011,1(4):185-191.

［3］黄志超, 赖家美,张永超.自冲铆接技术
［M］.南昌：江西高校出版社,2017.

Huang Z C, Lai J M, Zhang Y C. Self-piercing Riveting Technology
［M］. Nanchang: Jiangxi University Press, 2017.

［4］黄志超, 程露,胡义华.铝合金与碳纤维复合材料自冲铆接强度影响因素研究
［J］. 塑料工业,2019，47（5）：72-76.

Huang Z C, Cheng L, Hu Y H. Study on the influence factors of self-piercing riveting strength of aluminum alloy and carbon fiber composite
［J］. Plastic Industry,2019，47（5）：72-76.

［5］黄志超，宋天赐，赖家美.TA1钛合金自冲铆接接头疲劳性能及失效机理分析
［J］.焊接学报,2019,40（3）:41-46.

Huang Z C, Song T C，Lai J M. Fatigue property and failure mechanism analysis of TA1 titanium alloy self-piercing riveting joint
［J］.Journal of Welding,2019,40（3）:41-46.

［6］魏文杰，何晓聪，易金权，等.TA1铆焊复合接头与自冲铆接头力学性能对比
［J］.塑性工程学报，2019，26 (4): 207-212.

Wei W J，He X C，Yi J Q，et al. Comparison of mechanical properties between TA1 rivet-welding composite joint and SPR joint
［J］.Journal of Plasticity Engineering，2019，26(4):207-212.

［7］王端义. 基于数值模拟的6016/ST13钢铝异种板材自冲铆接成形
［J］.锻压技术，2019,44(9):68-72.

Wang D Y. Self-piercing riveting of 6016/ST13 steel-aluminum dissimilar sheet based on numerical simulation
［J］. Forging & Stamping Technology，2019,44(9):68-72.

［8］周琦. 基于数值模拟的铝合金板料自冲铆接成形
［J］.锻压技术，2019,44(7):47-51.

Zhou Q. Self-piercing riveting of aluminum alloy sheet based on numerical simulation
［J］. Forging & Stamping Technology，2019,44(7):47-51.

［9］Mucha J. The failure mechanics analysis of the solid self-piercing riveting joints
［J］.Engineering Failure Analysis,2015,47:77-88.

［10］Mucha J. The numerical analysis of the effect of the joining process parameters on self-piercing riveting using the solid rivet
［J］. Archives of Civil and Mechanical Engineering,2014,14:444-454.

［11］王健强，潘伟涛，钱让发，等.7075铝合金预加热处理对自冲铆接质量的提升
［J］.机床与液压，2019，47(14):181-183.

Wang J Q，Pan W T，Qian R F，et al.Quality improvement of self-piercing riveting by the preheating treatment of 7075 aluminum alloy
［J］.Machine Tool ＆ Hydraulics，2019，47(14):181-183.

［12］王军伟. AZ31镁合金的自冲铆接工艺研究
［D］.郑州：郑州大学,2010.

Wang J W . Study on Self-piercing Riveting Process of AZ31 Magnesium Alloy
［D］. Zhengzhou：Zhengzhou University,2010.

［13］杨江，彭建，孙松，等.变形程度对镁合金板材力学性能和耐腐蚀性能的影响
［J］.稀有金属,2018，42,(1):21-28.

Yang J, Peng J, Sun S, et al. Effect of deformation degree on mechanical properties and corrosion resistance of magnesium alloy plate
［J］. Chinese Journal of Rare Metals, 2018, 42 (1): 21-28.

［14］钦兰云，李明东，杨光，等.热处理对激光沉积TC4钛合金组织与力学性能的影响
［J］.稀有金属，2018,42（7）：698-704.

Qin L Y, Li M D, Yang G, et al. Effect of heat treatment on microstructure and mechanical properties of laser deposited TC4 titanium alloy
［J］. Chinese Journal of Rare Metals, 2018, 42 (7): 698-704.

［15］卢毅, 何晓聪,邢保英，等.退火处理对钛合金自冲铆接头疲劳特性的影响
［J］.焊接学报,2018,39(3):124-128.

Lu Y, He X C, Xing B Y, et al. Effect of annealing on fatigue properties of self-piercing riveted joint of titanium alloy
［J］.Journal of Welding,2018,39(3):124-128.

服务与反馈：

【文章下载】【加入收藏】