网站首页期刊简介编委会过刊目录投稿指南广告合作征订与发行联系我们English
内压对小直径薄壁U型波纹管成形规律的影响
英文标题:Effect of internal pressure on forming law of thin-wall U-shaped bellows with small diamete
作者:李凯 苗晓军 皇涛 蒋宇宁 赵家鑫 
单位:平高集团有限公司 河南科技大 有色金属共性技术河南省协同创新中心 
关键词:波纹管 内压 成形规律 壁厚减薄率 数值模拟 
分类号:TG376
出版年,卷(期):页码:2020,45(10):66-72
摘要:

 为了研究内压对小直径薄壁U型波纹管的壁厚减薄率的影响行为,采用数值模拟分析的方法,基于ANSYS/LS-DYNA有限元分析软件,建立了小直径薄壁U型316L奥氏体不锈钢波纹管的内压成形过程的有限元模型,获得了小直径薄壁U型波纹管内压成形过程中的等效应力、等效应变和壁厚减薄率的分布演变规律。在相同的轴向进给位移条件下,获得了不同的内压对小直径薄壁U型波纹管的壁厚减薄率分布的影响规律,获得了成形质量合格的小直径薄壁U型波纹管的成形内压范围,研究结果为小直径薄壁U型波纹管的内压成形工艺的设计提供了数据参考。

 In order to study the effect behavior of internal pressure on the wall thickness thinning rate of thin-wall U-shaped bellows with small diameter, using the numerical simulation analysis method, the finite element model of internal pressure forming process for the thin-wall U-shaped 316L austenitic stainless steel bellows with small diameter was established based on ANSYS/LS-DYNA finite element analysis software. The distributions and evolution laws of equivalent stress, equivalent strain and wall thickness thinning rate during the internal pressure forming process of thin-wall U-shaped bellows with small diameter were obtained. The effect law of different pressures on the wall distribution of thickness thinning rate for thin-wall U-shaped bellows with small diameter under the same axial feeding displacement conditions was obtained. The forming internal pressure range of qualified forming thin-wall U-shaped bellows with small diameter was obtained. The research results provide the data reference to the design of internal pressure forming process for thin-wall U-shaped bellows with small diameter.

基金项目:
国家自然科学基金资助项目(51875176);国家电网有限公司总部科技资助项目(B491 BG190013)
作者简介:
李凯(1984-),男,硕士,高级工程师 E-mail:007zzulikai@163.com 通讯作者:皇涛(1983-),男,博士,副教授 E-mail:huangtao@haust.edu.cn
参考文献:

 
[1]唐治东.波纹管液压成形过程的数值模拟与实验研究
[D].杭州:浙江工业大学, 2015.


Tang Z D. Numerical Simulation and Experimental Study of Hydroforming Process of Bellows
[D]. Hangzhou: Zhejiang University of Technology, 2015. 


[2]Abrantes J P, Szabo-Ponce A, CtF Batalha. Experimental and numerical simulation of tube hydroforming
[J]. Journal of Materials Processing Technology, 2005, 164(15): 1140-1147.


[3]李艳艳.V形膨胀节的承载和补偿能力分析及膨胀节成形过程的模拟
[D].北京:北京化工大学,2009.

Li Y Y. V-shaped Expansion Joint Load-bearing and Compensation Capacity Analysis and Expansion Joint Forming Process Simulation
[D]. Beijing: Beijing University of Chemical Technology, 2009.



[4]Yuan S, Yuan W, Wang X. Effect of wrinkling behavior on formability and thickness distribution in tube hydroforming
[J]. Journal of Materials Processing Technology, 2006, 177(1-3):668-671.


[5]王小松,苑世剑,王仲仁.内高压成形起皱行为的研究
[J].金属学报,2003, 39(12): 1276-1280.

Wang X S, Yuan S J, Wang Z R. Research on wrinkling behavior of internal high pressure forming
[J]. Acta Metallurgica Sinica, 2003, 39(12): 1276-1280.


[6]汤泽军,何祝斌,苑世剑.内高压成形过程塑形失稳起皱分析
[J].机械工程学报,2008, 44(5): 34-38. 

Tang Z J, He Z B, Yuan S J. Analysis of wrinkling during instability during internal high pressure forming
[J]. Journal of Mechanical Engineering, 2008, 44(5): 34-38.


[7]苑文婧,刘晓航,田浩彬.双锥形管液压成形过程中破裂和起皱的力学条件
[J].上海第二工业大学学报, 2012, 29(1): 12-19.

Yuan W J, Liu X H, Tian H B. The mechanical conditions of rupture and wrinkling during the hydroforming of the double-cone tube
[J]. Journal of Shanghai Second Polytechnic University, 2012, 29(1): 12-19.


[8]郭煜敬,王志刚,金光耀,等. 液压成形波纹管减薄率的数值模拟研究
[J].浙江工业大学学报,2019,47(1):58-62.

Guo Y J, Wang Z G, Jin G Y, et al. Numerical simulation of the thinning rate of hydroformed bellows
[J]. Journal of Zhejiang University of Technology, 2019, 47(1): 58-62.


[9]Fang K J, Hsiao P Y. Optimization of loading conditions for tube hydroforming
[J]. Journal of Materials Processing Technology, 2003, 140: 520-524.


[10]Yang J B,Jeon B H,Oh S I. Design sensitivity analysis and optimization of the hydroforming process
[J]. Journal of Materials Processing Technology,2001,113(1/2/3):666-672.


[11]崔磊,刘静,李兰云. 基于响应面法的双层316L/Inconel625波纹管液压胀形工艺参数优化
[J].兵器材料科学与工程,2018,41(6):19-26.

Cui L, Liu J, Li L Y. Optimization of hydraulic bulging process parameters of double-layer 316L/Inconel625 bellows based on response surface method
[J]. Ordnance Material Science and Engineering, 2018, 41(6):19-26.


[12]陈杰.管材内高压成形数值模拟与工艺研究
[D].上海:上海交通大学,2013.

Chen J. Numerical Simulation and Process Study of High Pressure Forming in Pipes
[D]. Shanghai: Shanghai Jiao Tong University, 2013.


[13]唐治东.波纹管液压成形过程的数值模拟与实验研究
[D].杭州:浙江工业大学,2015.

Tang Z D. Numerical Simulation and Experimental Research on the Process of Bellows Hydroforming
[D].Hangzhou:Zhejiang University of Technology, 2015.

服务与反馈:
本网站尚未开通全文下载服务】【加入收藏
《锻压技术》编辑部版权所有

中国机械工业联合会主管 北京机电研究所有限公司 中国机械工程学会塑性工程分会主办
联系地址:北京市海淀区学清路18号 邮编:100083
电话:+86-010-62920652 +86-010-82415085 传真:+86-010-62920652
E-mail: fst@263.net(稿件) dyjsjournal@163.com(广告)
京ICP备09032115号-5