网站首页期刊简介编委会过刊目录投稿指南广告合作征订与发行联系我们English
基于修正JohnsonCook模型的HNi56-3镍黄铜合金 高温流变行为研究
英文标题:Research on high-temperature rheological behavior for HNi56-3 nickel brass alloy based on modified Johnson-Cook model
作者:马斌 梁强 李平 
单位:1. 重庆工商大学 机械工程学院 2. 重庆工商大学 制造装备机构设计与控制重庆市重点实验室 
关键词:HNi56-3镍黄铜合金 高温流变行为 修正JC模型 应变速率 变形温度 
分类号:TG146.1
出版年,卷(期):页码:2020,45(11):200-205
摘要:

 以HNi56-3镍黄铜合金为研究对象,分别在变形温度范围为600~800 ℃、应变速率范围为0.01~10 s-1的变形条件下,在Gleeble-3500热模拟实验机上进行等温热压缩实验,研究HNi56-3镍黄铜合金的高温流变行为。实验结果表明:HNi56-3镍黄铜合金的流变应力与变形温度、应变速率和应变呈非线性关系,流变应力随着应变速率和应变的增大而升高、随着变形温度的升高而降低。为了描述HNi56-3镍黄铜合金的流变行为,使用Lin Y C修正的JohnsonCook模型(LinJC)和本文修正的JC模型(MLinJC)分别建立本构模型。对比两种模型,结果显示:基于LinJC模型的预测数据的平均相对误差绝对值AARE为11.8644%,相关系数R为0.9803,均方根误差RMSE为4.6177 MPa;本文构建的MLinJC模型的预测数据的AARE为4.0325%,R为0.9936,RMSE为1.9017 MPa,因此,本文建立的本构模型与实验结果更吻合,能更准确地描述HNi56-3镍黄铜合金的高温流变行为。

 For HNi56-3 nickel brass alloy, the isothermal thermal compression experiments were conducted by Gleeble-3500 thermo-mechanical simulator under the deformation temperatures of 600-800 ℃ and the strain rates of 0.01-10 s-1, and the high-temperature rheological behavior of HNi56-3 nickel brass alloy was studied. The experimental results show that the rheological stress of HNi56-3 nickel brass alloy has a nonlinear relationship with deformation temperature, strain rate and strain, and the rheological stress increases with the increasing of strain rate and strain, and decreases with the increasing of deformation temperature. In order to describe the rheological behavior of HNi56-3 nickel brass alloy, the constitutive models were established by Lin-JC model modified by Lin Y C and Mlin-JC model modified by this paper. Comparing two models, the results show that the absolute value of average absolute relative error AARE of  prediction data based on Lin-JC model is 11.8644%, the correlation coefficient R is 0.9803, and the root mean squared error RMSE is 4.6177 MPa. However, the corresponding values of AARE, R and RMSE based on MLin-JC model are 4.0325%, 0.9936 and 1.9017 MPa respectively. Thus, the prediction accuracy based on MLin-JC model is better, and the MLin-JC model can accurately describe the high-temperature rheological behavior of HNi56-3 nickel brass alloy.

 
基金项目:
重庆市基础科学与前沿技术研究专项基金资助项目(cstc2017jcyjAX0175);重庆市教育委员会科学技术研究项目(KJQN201900836);重庆工商大学校内科研项目(1752009)
作者简介:
马斌(1971-),男,硕士,实验师 E-mail:mabin@ctbu.edu.cn
参考文献:

 [1]胥锴,张书权,顾伟,等.环保易切削黄铜的发展现状及前景[J].上海有色金属,2008, 29(2):88-90.


Xu K, Zhang S Q, Gu W, et al. Present status and prospects of environmental protection type free cutting brass [J].Shanghai Nonferrous Metals, 2008, 29(2):88-90.


[2]王梦寒,危康,李小娟,等.高强锰黄铜高温热流变行为及本构方程的建立[J].Journal of Central South University,2018, 25(7):1560-1572.


Wang M H, Wei K, Li X J, et al. Constitutive modeling for high temperature flow behavior of a highstrength manganese brass [J]. Journal of Central South University, 2018, 25(7): 1560-1572.


[3]王梦寒,夏知姿,李雁召,等.锰黄铜合金高温变形及本构模型研究[J].热加工工艺,2016, 45(4):46-48.


Wang M H, Xia Z Z, Li Y Z, et al. Research on high temperature deformation and constitutive model of Mn brass alloy [J].Hot Working Technology,2016, 45(4):46-48.


[4]王文浩. 黄铜齿环精密锻造成形及模具磨损研究[D].重庆:重庆大学,2013.


Wang W H. Study on Precision Forging Process and Die Wear of Brass Synchronizer Ring [D].Chongqing: Chongqing University, 2013.


[5]王延辉,龚冰,李冰.H65黄铜合金热变形流变应力特征研究[J].塑性工程学报, 2008,15(6):113-117.


Wang Y H, Gong B, Li B. Flow stress of H65 brass alloy during hot compression deformation [J]. Journal of Materials Plasticity  Engineering, 2008, 15(6):113-117.


[6]乔景振,田保红,张毅,等.Cu-7Ni-7Al-2Fe-2Mn-0.5Ti合金高温热变形行为[J].材料热处理学报, 2018, 39(3):131-135.


Qiao J Z, Tian B H, Zhang Y, et al. Hot deformation behavior of Cu-7Ni-7Al-2Fe-2Mn-0.5Ti alloy[J].Transaction of Materials and Heat Treatment,2018, 39(3):131-135.


[7]李建云. 硅黄铜热变形特征及组织演变规律的研究[D].赣州:江西理工大学,2014.


Li J Y. Research on Thermal Deformation Characteristics and Microstructure Evolution of Silicon Brass Alloy [D].Ganzhou:Jiangxi University of Science and Technology, 2014.


[8]Liu N, Li Z, Li L, et al. Processing map and hot deformation mechanism of novel nickelfree white copper alloy [J]. Transactions of Nonferrous Metals Society of China, 2014, 24(11):3492-3499.


[9]Wang Y, Zhou Y X, Xia Y M. A constitutive description of tensile behavior for brass over a wide range of strain rates [J]. Materials Science & Engineering A, 2004, 372(1):186-190.


[10]Lin Y C, Chen X M, Liu G. A modified Johnson-Cook model for tensile behaviors of typical highstrength alloy steel [J]. Materials Science & Engineering A, 2010, 527(26):6980-6986.


[11]Lin Y C, Chen M S, Zhang J. Modeling of flow stress of 42CrMo steel under hot compression [J]. Materials Science & Engineering: A (Structural Materials: Properties, Microstructure and Processing), 2009, 499(1-2):88-92.


[12]Tao Z J, Fan X G, Yang H, et al. A modified Johnson-Cook model for NC warm bending of large diameter thinwalled Ti-6Al-4V tube in wide ranges of strain rates and temperatures [J]. Transactions of Nonferrous Metals Society of China, 2018, 28(2):298-308.


[13]Zhao Y H, Sun J, Li J F, et al. A comparative study on JohnsonCook and modified JohnsonCook constitutive material model to predict the dynamic behavior laser additive manufacturing FeCr alloy [J]. Journal of Alloys and Compounds, 2017, 723:179-187.


[14]Johnson G R, Cook W H. A constitutive model and data for metals subjected to large strains, high strain rates and high temperatures [J]. Engineering Fracture Mechanics, 1983, 21:541-548.


[15]叶建华, 陈明和, 王宁, . 基于修正JC模型的TA12钛合金高温流变行为[J]. 中国有色金属学报, 2019, 29(4):75-83.


Ye J H, Chen M H, Wang N, et al. Flow behavior of TA12 titanium alloy based on modified JC model at high temperature [J]. The Chinese Journal of Nonferrous Metals, 2019, 29(4):75-83.

服务与反馈:
文章下载】【加入收藏
《锻压技术》编辑部版权所有

中国机械工业联合会主管  中国机械总院集团北京机电研究所有限公司 中国机械工程学会主办
联系地址:北京市海淀区学清路18号 邮编:100083
电话:+86-010-82415085 传真:+86-010-62920652
E-mail: fst@263.net(稿件) dyjsjournal@163.com(广告)
京ICP备07007000号-9