锻压技术

基于有限元法的三通管接头多向模锻成形仿真与优化

英文标题：Simulation and optimization on multi-directional die forging for tee pipe joint based on finite element method

作者：孙国柱

单位：无锡工艺职业技术学院

分类号：TG316.3

出版年,卷(期):页码：2021,46(2):28-33

摘要：

针对三通管接头在模锻成形中易出现破裂、材料折叠、冲头载荷大等问题，研究了冲头速度、坯料初始温度、摩擦系数对锻件模锻质量的影响。通过Deform软件，研究了水平冲头和垂直冲头等速进给、水平冲头和垂直冲头差速进给、水平冲头进给而垂直冲头不运动3种工艺条件下锻件的成形规律，并基于上述最佳工艺，研究了坯料初始温度对模锻过程中温度分布的影响,以及摩擦系数对锻件等效应变的影响，以获得最优的工艺参数。结果表明：在水平冲头和垂直冲头差速进给的情况下锻件质量较好，最优工艺参数能够显著降低冲头载荷，通过与试验结果对比，验证了有限元仿真结果的正确性，为类似管件模锻工艺的研究提供了理论参考。

For the problems such as fracture, material folding and heavy punch load in the die forging process of tee pipe joint, the influences of punch speed, initial temperature of billet and friction coefficient on the die forging quality of forgings were studied, and the forming laws of forgings under three technological conditions of feeding at the same speed for horizontal punch and vertical punch, feeding at different speeds for horizontal punch and vertical punch and feeding of horizontal punch and not moving of vertical punch were studied by software Deform. Based on the above-mentioned optimal process, the influence of initial temperature for billet on the temperature distribution in the die forging process and the influence of friction coefficient on the equivalent strain of forgings were studied to obtain the optimal process parameters. The results show that the forging quality is better under the condition of feeding at different speeds for horizontal punch and vertical punch, and the punch load reduces significantly under the optimal process parameters. By comparing with the test results, the correctness of the finite element simulation results is verified, which provides a theoretical reference for the research of die forging process for similar pipes.

基金项目：

孙国柱（1976-），男，硕士，实验师，工程师，E-mail：157294889@qq.com

参考文献：

[1]高远，黄尚宇，邓凌波，等. 温度条件对铜管/铝管磁脉冲-半固态复合辅助钎焊接头微观组织的影响 [J].锻压技术，2019,44(10):169-175.
Gao Y，Huang S Y，Deng L B，et al. Influence of temperature condition on microstructure of Cu tube/Al tube brazed joint produced by magnetic pulse and semi-solid composite auxiliary technology [J].Forging & Stamping Technology，2019,44(10):169-175.
[2]刘张羽,孙亮,惠虎,等.内压作用下焊制四通的塑性极限分析[J].压力容器,2019,36(9):22-27,21.
Liu Z Y,Sun L,Hui H,et al.Plastic limit analysis of the welded cross under loads of internal pressure[J].Pressure Vessel Technology,2019,36(9):22-27,21.
[3]朱正才. 三通管接头简易热锻模设计与制造[J]. 热加工工艺,2012,41(23):222-223.
Zhu Z C.Design and manufacture of simple heat forging die for tube fittings[J].Hot Working Technology,2012,41(23):222-223.
[4]赵洁,闫洪波,侯永亮. 基于Deform的三通阀体热锻成形工艺优化[J]. 热加工工艺,2019,48(21):96-98.
Zhao J,Yan H B,Hou Y L.Optimization of hot forging process for three-way valve body based on deform[J].Hot Working Technology,2019,48(21):96-98.
[5]翟华,黄照森,崖华青,等. 基于Oyane准则的三通阀体横向法兰热成形起裂分析[J]. 塑性工程学报,2018,25(4):225-233.
Zhai H,Huang Z S,Ya H Q,et al.Crack analysis in hot forming process of tee-joint valve′s horizontal flange based on Oyane criterion[J].Journal of Plasticity Engineering,2018,25(4):225-233.
[6]顾文俊. 空排止回阀阀体多向模锻工艺研究[D].合肥：合肥工业大学,2019.
Gu W J.Research on Multidirectional Forging Process for Check Valve Body[D].Hefei：Hefei University of Technology,2019.
[7]张超，赵升吨，卢孟康，等. 4032铝合金活塞的热模锻变形过程有限元分析 [J]. 锻压技术，2019,44(11):1-10.
Zhang C，Zhao S D，Lu M K，et al. Finite element analysis on hot die forging deformation process for 4032 aluminum alloy piston [J]. Forging & Stamping Technology，2019,44(11):1-10.
[8]任运来,曹峰华,任杰,等. 水平带法兰三通阀体多向模锻工艺研究[J]. 上海电机学院学报,2015,18(5):249-254.
Ren Y L,Cao F H,Ren J,et al.Multi-ram die forging process of triple-valve body with horizontal flange[J].Journal of Shanghai Dianji University,2015,18(5):249-254.
[9]庄武豪. 弯头与三通管接头分模锻造成形规律研究[D].武汉：武汉理工大学,2014.
Zhuang W H.Investigation on Partible-die Forging Technology for the Elbow and Triple Valve[D].Wuhan: Wuhan University of Technology,2014.
[10]王睿. 基于Deform软件的四通管道阀热锻过程模拟及模具优化设计[J]. 热加工工艺,2018,47(13):177-180.
Wang R.Hot forging process simulation and die optimization design of four way pipeline valve based on Deform software[J].Hot Working Technology,2018,47(13):177-180.
[11]侯梅英,曹静. 工艺参数对弯管接头模锻质量的影响[J]. 热加工工艺,2019,48(13):113-115,123.
Hou M Y,Cao J.Effect of process parameters on die forging quality of elbow joint[J].Hot Working Technology,2019,48(13):113-115,123.
[12]吴艳云,张东民,盛育东,等. SCM435合金钢紧固件精冲过程的数值模拟及参数优化[J]. 中国科技论文,2018,13(4):474-477.
Wu Y Y,Zhang D M,Sheng Y D,et al.Numerical simulation and parameter optimization of the fine blanking process of SCM435 alloy steel[J].China Science Paper,2018,13(4):474-477.

服务与反馈：

【文章下载】【加入收藏】