锻压技术

基于挤压成形再冲压工艺的后悬弹簧连杆轻量化设计方法

英文标题：Lightweight design method on rear suspension spring connecting rod based on extrusion and stamping process

作者：黄志超彭晓亮汪伟张帆

单位：华东交通大学

分类号：TH164

出版年,卷(期):页码：2021,46(5):25-33

摘要：

传统后悬弹簧连杆制造工艺繁多，且在实际工作过程中的耐久性和强度等性能表现并不佳。通过引用新型铝合金材料，以挤压成形为冲压毛坯成形工艺，并结合成熟的冲压工艺，取消了电泳后处理工艺，而且重新设计了零件结构，从而设计出新型铝镁硅可热处理强化合金的后悬弹簧连杆。通过有限元模拟分析进行初步设计，并利用试验车以及台架试验验证有限元模拟分析的准确性和设计思路的可行性。结果表明：新设计有较好的可制造性，其重量相比原冲压焊接设计减少了40%，强度性能提高了38%，刚度性能接近原钢件设计。无焊接变形的新工艺明显减少了四轮定位参数的变化量，提高了轮胎使用寿命，而且悬架整体硬点不变，且成本略有减低。

There are too many manufacturing processes for the traditional rear suspension spring connecting rod, and the performances of durability and strength in the actual working process are not good. Therefore, a new rear suspension spring connecting rod of aluminum-magnesium-silicon heat-treatable and strengthened alloy was designed by quoting new aluminum alloy material, using extrusion process as stamping blank forming process, combining with mature stamping process, canceling the electrophoretic post-treatment process and redesigning part structure. Then, the initial design was conducted by the finite element simulation analysis, and the accuracy of finite element simulation analysis and the feasibility of new design were verified by the vehicle testing and bench test. The results show that the new design has good manufacturability, the weight reduces by 40% compared with the original stamping and welding design, the strength performance improves by 38%, and the stiffness performance is close to that of the original steel part. Thus, the new process without welding deformation obviously reduces the variation of four-wheel alignment parameters and improves the service life of tire. In addition, the overall hard point of suspension remains unchanged, and the cost is slightly reduced.

基金项目：

江西省重点研发计划一般项目（20192BBEL50013）

黄志超(1971-)，男，博士，教授 E-mail：hzcosu@163.com

参考文献：

[1]陈家瑞.汽车构造[M]. 北京：机械工业出版社，2005.

Cheng J R. Automobile Structure[M]. Beijing: China Machine Press, 2005.

[2]徐从昌，孙朝蓉，于婉玉,等. 轻量化车身用AlMgSi 合金时效工艺及强化相析出行为研究进展[J]. 塑性工程学报,2019,26(4):10-16.

Xu C C, Sun C R, Yu W Y, et al. Research progress in aging process and precipitation behavior of strengthening phase in AlMgSi alloy used for lightweightvehicle body [J]. Journal of Plasticity Engineering,2019,26(4):10-16.

[3]张伟. 基于侧面碰撞特性的B 柱总成轻量化设计分析 [J]. 塑性工程学报,2019,26(4):150-158.

Zhang W. Analysis of lightweight design of B-pillar assembly based on side impact characteristics [J]. Journal of Plasticity Engineering,2019,26(4):150-158.

[4]廖本洪，时来鑫，胡励. 退火工艺对高温叠轧AZ31 镁合金板材组织与性能的影响[J].锻压技术，2020,45（3）:180-183.

Liao B H,Shi L X, Hu L. Effect of annealing process on microstructure and properties of high temperature roll bonding for AZ31 magnesium alloy sheet [J]．Forging ＆ Stamping Technology，2020,45（3）:180-183.

[5]沈鸿.机械工程手册[M]，北京：机械工业出版社，2005.

Shen H. Mechanical Engineering Handbook [M]. Beijing: China Machine Press, 2005.

[6]贾璐, 李永堂, 惠恬. 大口径厚壁管均匀性热挤压工艺研究[J]. 塑性工程学报,2020,27(5):133-143.

Jia L, Li Y T, Hui T. Uniformization hot extrusion of heavy caliber thick-walled pipe [J]. Journal of Plasticity Engineering,2020,27(5):133-143.

[7]余万铨，胡志力，杨冰，等. 某铝合金汽车发动机罩外板冲压成形工艺[J]. 锻压技术，2020，45（4）:45-50.

Yu W Q，Hu Z L，Yang B，et al. Stamping process of automobile engine outer panel for aluminum alloy [J]. Forging ＆ Stamping Technology，2020，45（4）：45-50.

[8]郝启,汪亚利,徐成龙,等.机械臂连杆设计探讨[J].成组技术与生产现代化,2018,35(2):44-48.

Hao Q, Wang Y L, Xu C L, et al. Research on the design of manipulator connecting rod[J].Group Technology & Production Modernization,2018,35(2):44-48.

[9]王红民,谢锋,郑国峰,等.汽车悬架控制臂拉压溃分析及疲劳寿命预测[J].振动与冲击,2016,35(20):41-46.

Wang H M, Xie F, Zeng G F, et al. Collapse analysis and fatigue life prediction of a vehicle suspension control arm[J].Journal of Vibration and Shock,2016,35(20):41-46.

[10]刘静安.铝型材断面设计及可挤压范围分析[J].有色金属加工,2004,33(1):37-42.

Liu J A. Section design and extrusion limit analysis of aluminum profile[J].Nonferrous Metals Processing,2004,33(1):37-42.

[11]马闻宇.AA6082铝合金热冲压成形性规律控制规律研究及工艺优化[D].北京：北京科技大学，2016.

Ma W Y. Research on Law Formability and Property for Hot Stamping AA6082 Alumium Alloy and Process Optimization[D].Beijing: University of Science and Technology Beijing，2016.

[12]余万铨，胡志力. 某铝合金汽车发动机罩外板冲压成形工艺[J].锻压技术，2020,45（4）:46-50.

Yu W S, Hu Z L. Stamping process of automobile engine outer panel for aluminum alloy[J]. Forging ＆ Stamping Technology，2020，45（4）:46-50.

[13]单柯日,黄长明,刘建平.铝合金控制臂的轻量化设计及挤压铸造工艺[J].特种铸造及有色合金,2016,36(5):484-487.

Shan K R, Huang C M, Liu J P. Light design and extrusion casting process for aluminum control arm[J]. Special Casting & Nonferrous Alloys, 2016, 36(5):484-487.

[14]程喆,钱东升. 2219 铝合金构筑成形工艺实验与界面愈合规律[J]．锻压技术，2020,45（12）:172-177.

Chen J, Qian D S. Additive forming process experiment and interface healing law for 2219 aluminum alloy[J]. Forging & Stamping Technology，2020,45（12）:172-177.

[15]杨婻,孟宣宣.汽车用挤压铝零件的断面优化[J].汽车与配件,2014,(32):46-48.

Yang N, Meng X X. Section design and extrusion limit analysis of aluminum profile[J].Automobile & Parts,2014,(32):46-48.

[16]张宏远,覃士耘.基于参数化模型的柴油机连杆结构轻量化设计[J].内燃机与配件,2019,(12):21-23.

Zhang H Y, Qin S Y. Lightweight design of connecting rod structure of diesel engine based on parametric model[J].Internal Combustion Engine & Parts,2019,(12):21-23.

[17]刘勇，耿会程. 高强铝合金高效热冲压工艺研究进展[J]．锻压技术，2020，45（7）:1-10.

Liu Y, Geng H C. Research progress on high efficiency hot stamping process for high strength aluminum alloy[J]. Forging ＆ Stamping Technology，2020, 45（7）:1-10.

[18]孙伟领，丁金根，边翊，等．铝合金控制臂锻造工艺参数优化与缺陷分析[J]．锻压技术，2019,44（5）：29-34.

Sun W L，Ding J G，Bian Y，et al． Optimization on forging process parameters and defect analysis for aluminum alloy control arm[J]. Forging ＆ Stamping Technology，2019,44（5）：29-34.

服务与反馈：

【文章下载】【加入收藏】