网站首页期刊简介编委会过刊目录投稿指南广告合作征订与发行联系我们English
基于DEFORM的直齿圆柱齿轮精锻工艺
英文标题:Precision forging process for spur gear based on DEFORM
作者:卜军伟 蔡云 
单位:四川交通职业技术学院 西华大学 
关键词:直齿圆柱齿轮 无飞边模锻 浮动凹模 模具载荷 模具寿命 孔分流法 
分类号:TG316.3
出版年,卷(期):页码:2021,46(11):43-48
摘要:

 为了节约成本、提高材料的利用率、提高产品的质量及生产效率,无飞边模锻工艺的应用越来越广泛,但不免遇到模具承受载荷过大、寿命低的问题。以某直齿圆柱齿轮为研究对象,采用DEFORM3D软件对其模锻成形过程进行数值模拟,并针对成形力大、模具寿命低的问题,在原工艺基础上提出了采用浮动凹模及孔分流法两种改进工艺,分别分析了锻件的成形规律及模具载荷变化情况。结果表明:改进后的工艺有利于降低模具载荷、提高模具的使用寿命;采用浮动凹模工艺,模具载荷可以降低10%;采用孔分流工艺,模具载荷可以降低25%。

  In order to save costs, improve the utilization rate of materials, and improve the quality and production efficiency of products, the application of non-flanging die forging process is more and more widely used, but it is inevitable to encounter the problems of excessive load and low mold life. Therefore, for a spur gear, its die forging process was simulated by software DEFORM-3D. Aiming at the problems of large forming force and low mold life, on the basis of the original process, two improved processes, namely floating die and hole split method, were proposed, and the forming laws of forgings and the changes of mold load were analyzed respectively. The results show that the improved process is beneficial to reduce the mold load and prolong the service life of mold, and by adopting the floating die and hole split processes, the mold load is reduced by 10% and 25%, respectively.

基金项目:
四川省教育厅科研项目(14ZA0358)
作者简介:
作者简介:卜军伟(1985-),男,学士,讲师,E-mail:hezebdm@163.com;通信作者:蔡云(1979-),男,硕士,副教授,E-mail:noyi921@yeah.net
参考文献:

 [1]夏巨谌. 闭式模锻[M]. 北京:机械工业出版社, 1993.


Xia J C.Closed Die Forging[M].Beijing: China Machine Press,1993.


[2]赵伟平, 刘江涛,贾倩.基于Deform的齿轮泵从动齿轮轴闭式模锻数值模拟分析[J].热加工工艺,2020,49(13):93-95,99.


Zhao W P,Liu J T,Jia Q.Numerical simulation and analysis of closed die forging of gear pump follower gear shaft based on Deform[J].Hot Working Technology,2020,49(13):93-95,99.


[3]陈庆敏, 孟凡响,李丽,.铁道车辆钩舌闭式模锻工艺的数值模拟研究[J].锻压技术,2019,44(7):1-6.


Chen Q M,Meng F X,Li L,et al.Numerical simulation on closed die forging process for railway vehicle knuckle[J].Forging Stamping Technology,2019,44(7):1-6.


[4]包卫平. 热锻模的典型失效形式及其原因分析[J].锻造与冲压,2020,(5):28,30-32.


Bao W P.Typical failure forms of hot forging die and its cause analysis[J].Forging and Metalforming,2020,(5):28,30-32.


[5]陆宝山, 王雷刚,季业益,.金属成形热力耦合模拟与模具失效机制研究[J].塑性工程学报,2019,26(3):33-40.


Lu B S,Wang L G,Ji Y Y,et al.Study on thermomechanical coupling simulation of metal forming and failure mechanisms of forging die[J].Journal of Plasticity Engineering,2019,26(3):33-40.


[6]王相钧, 王大勇,王培涛,.连接杆头模锻工艺参数优化研究[J].塑性工程学报,2019,26(6):36-41.


Wang X J,Wang D Y,Wang P T,et al.Process parameters optimization of die forging for connecting rod head[J].Journal of Plasticity Engineering,2019,26(6):36-41.


[7]韦光珍, 张玉平,王东.锻造比对新型锻造模具钢磨损和冲击性能的影响[J].热加工工艺,2020,49(11):111-113.


Wei G Z,Zhang Y P,Wang D.Effect of forging ratio on wear and impact properties of new forging die steel[J].Hot Working Technology,2020,49(11):111-113.


[8]刘雅辉. 发动机连杆热锻成形数值模拟及模具结构优化[D]. 上海:上海工程技术大学,2015.


Liu Y H.The Numerical Simulation of Hot Forging and Die Structure Optimization for Engine Connecting Rod[D].ShanghaiShanghai University of Engineering Science,2015.


[9]杜立东. 热模锻自动线喷淋润滑系统应用[J].金属加工:热加工,2015(9):14-16.


Du L D.Application of spray lubrication system in hot die forging automatic line[J].MW Metal Forming,2015, (9):14-16.


[10]姜峰, 李波.基于ANSYS的汽车变速箱直齿轮闭式模锻工艺仿真分析[J].热加工工艺,2019,48(17):85-88.


Jiang F,Li B.Simulation and analysis of closed die forging technology for automobile gearbox spur gear based on ANSYS[J].Hot Working Technology,2019,48(17):85-88.


[11]张东民, 盛育东,周伟民,.SCM435合金钢线材浮动反挤压成形模拟及参数优化[J].铸造技术,2017,38(11):2698-2700.


Zhang D M,Sheng Y D,Zhou W M,et al.Forming simulation and parameter optimization of floating back extrusion for SCM435 alloy steel wires[J].Foundry Technology,2017,38(11):2698-2700.


[12]胡建军. DEFORM3D塑性成形CAE应用教程[M]. 北京:北京大学出版社, 2011.


Hu J J.CAE Application Course of DEFORM3D Plastic Forming[M].Beijing: Peking University Press,2011.


[13]王以华. 锻模设计技术及实例[M]. 北京:机械工业出版社, 2009.


Wang Y H.Forging Die Design Technology and Examples[M].Beijing: China Machine Press,2009.

服务与反馈:
文章下载】【加入收藏
《锻压技术》编辑部版权所有

中国机械工业联合会主管  中国机械总院集团北京机电研究所有限公司 中国机械工程学会主办
联系地址:北京市海淀区学清路18号 邮编:100083
电话:+86-010-82415085 传真:+86-010-62920652
E-mail: fst@263.net(稿件) dyjsjournal@163.com(广告)
京ICP备07007000号-9