锻压技术

压力机齿轮传动系统的仿真与试验

英文标题：Simulation and experiment of gear transmission system for press

作者：于涛刘国栋李金耀陈宝鑫于蓉蓉

分类号：TH132.413

出版年,卷(期):页码：2021,46(12):169-173

摘要：

为了对压力机及其传动系统的故障诊断进行研究，以JM21160曲柄压力机的齿轮传动系统为研究对象，对齿轮传动系统的啮合频率在理论上进行了计算，得到其啮合频率为82.499 Hz,并对齿轮啮合理论中的调幅调频现象进行了分析。通过CREO和ADAMS分别对齿轮进行了建模和仿真，并且对JM21160曲柄压力机进行了振动试验测试。通过理论、仿真和试验数据的对比，发现三者得到的齿轮啮合频率在数值上基本相等，进而对JM21160曲柄压力机的齿轮传动系统啮合理论的调幅调频现象和仿真结果进行了验证，证明了理论方法的正确性和仿真的可靠性，为后续研究压力机故障诊断方法奠定了理论和仿真基础。

In order to research the fault diagnosis of press and its transmission system, for the gear transmission system of crank press JM21-160, the meshing frequency of gear transmission system was theoretically calculated as 82.499 Hz, and the amplitude and frequency modulation phenomenon in the theory of gear meshing was analyzed. Then, the gear was modeled and simulated by CREO and ADAMS respectively, and the vibration test of crank press JM21-160 was carried out. By the contrast of theory, simulation and experimental data, the gear meshing frequencies obtained by the three were basically equal in values, and then the amplitude and frequency modulation phenomenon and the simulation result of gear transmission system meshing theory of crank press JM21-160 were verified. Thus, the correctness of theoretical method and the reliability of simulation were proved, which laid a theoretical and simulation basis for the follow-up research on the fault diagnosis method of press.

基金项目：

青年科学基金资助项目(52005302)

作者简介：于涛（1972-），男，博士，教授 E-mail：yutaosang@163.com 通信作者：于蓉蓉（1990-），女，博士，讲师 E-mail：rongrongyu19@sdust.edu.cn

参考文献：

[1] 范有发. 冲压与塑料成型设备[M]. 北京：机械工业出版社, 2010.

Fan Y F. Stamping and Plastic Forming Equipment[M]. Beijing: China Machine Press, 2010.

[2] 汪繁荣. 锻造液压机液压故障诊断专家系统研究[D].武汉：华中科技大学, 2004.

Wang F R. Study on Hydraulic Fault Diagnosis Expert System for Forging Hydraulic Press [D]. Wuhan: Huazhong University of Science and Technology, 2004.

[3] 张传锦, 高建波,王岩,等.压力机故障实时自诊断方法与系统[J].锻压技术,2020,45(6):136-140，157.

Zhang C J,Gao J B,Wang Y,et al. Realtime selfdiagnostic method and system for press fault[J]. Forging & Stamping Technology,2020,45(6):136-140,157.

[4] Loutas T H, Roulias D, Pauly E. The combined use of vibration, acoustic emission and oil debris online monitoring towards a more effective condition monitoring of rotating machinery[J]. Mechanical Systems and Signal Processing, 2011,(25): 1339-1352.

[5] Collacott R. Vibration and fatigue failure of turbine blades[J]. Shipbuilding and Shipping Record, 1941,(58): 105-106.

[6] 宋明. 监测诊断关键技术在高线轧机智能维修中的应用[J].设备管理与维修,2020,(3):143-144.

Song M. Application of monitoring and diagnosis key technologies in intelligent maintenance of high line mills [J]. Plant Management Engineering,2020,(3):143-144.

[7] 杨建鸣, 郑龙魁,高立新.基于齿轮啮合频率的轧机联轴器磨损监测诊断[J].机械设计与制造,2016,(8):43-45.

Yang J M,Zheng L K,Gao L X.Rolling mill coupling wear monitoring based on the diagnosis of meshing frequency[J]. Machinery Design & Manufacture,2016,(8):43-45.

[8] 潘林. 频谱分析法在齿轮故障诊断中的应用[J].石油化工设备技术,2019,40(1):5-6,19-21.

Pan L. Application of spectrum analysis method in gear fault diagnosis [J]. PetroChemical Equipment Technology,2019,40(1):5-6,19-21.

[9] 李光辉, 裴令明.齿轮座啮合频率对轧机传动系统振动的影响[J].冶金设备,2017,(3):26-29.

Li G H,Pei L M. Coupling resarch on tousional vibration and axial vibration of hot strip rolling mill[J].Metallurgical Equipment,2017,(3):26-29.

[10]Cooley C G, Parker R G. Eigenvalue sensitivity and veering in gyroscopic systems with application to highspeed planetary gears[J]. European Journal of MechanicsA/Solids, 2018,(67): 123-136.

[11]陈克兴. 设备状态检测与故障诊断技术[M].北京：科学技术文献出版社，1991.

Chen K X.Equipment Status Detection and Fault Diagnosis Technology[M]. Beijing: Scientific and Technical Documentation Press, 1991.

[12]丁康. 齿轮及齿轮箱故障诊断实用技术[M].北京：机械工业出版社，2005.

Ding K. Practical Technology of Gear and Gearbox Fault Diagnosis[M]. Beijing: China Machine Press, 2005.

[13]李栋. 调频波的频谱与塞贝尔函数[J]. 南通职大教学研究，1994,(1):6-10.

Li D. Frequency spectrum of frequencymodulated wave and the seibel function[J]. Journal of Nantong Vocational College, 1994,(1):6-10.

服务与反馈：

【文章下载】【加入收藏】