锻压技术

聚氨酯橡胶硬度对薄壁三通管内高压成形的影响

英文标题：Influence of polyurethane rubber hardness on internal high pressure forming for thin-walled T-tube

单位：1. 中航贵州飞机有限责任公司 2. 空军装备部驻安顺地区军事代表室 3. 沈阳航空航天大学

分类号：V262.3+2

出版年,卷(期):页码：2022,47(1):91-97

摘要：

以外径为Φ24 mm、壁厚为1.5 mm、长度为120 mm的H85黄铜管为例，以壁厚增减量不超过30%为合格品作为前提，以生成最大支管胀形高度的橡胶硬度为最佳参数，结合胀形实验和有限元仿真共同分析了60～90 HA范围内7种不同硬度的聚氨酯橡胶棒对等径三通管成形质量的影响。研究结果表明：随着橡胶硬度的逐渐增大，支管胀形高度增大，壁厚差减小，壁厚分布越均匀；当橡胶硬度大于85 HA时，支管顶部减薄率大于30%;当橡胶硬度小于70 HA时，直管端部和底部增厚率大于30%。此次研究中，橡胶硬度为85 HA时，成形三通管的最大壁厚为1.899 mm、最小壁厚为1.06 mm、支管胀形高度为17.132 mm，成形效果最佳。管坯整体壁厚分布规律为支管顶部减薄、直管端部增厚，且增厚区明显大于减薄区。

For H85 brass tube with outer diameter of Φ24 mm, wall thickness of 1.5 mm and length of 120 mm, taking the increase or decrease amount of wall thickness without exceeding 30% as a qualified product and the rubber hardness generating the maximum branch tube bulging height as the best parameter, combining the bulging experiment and finite element simulation, the influences of the polyurethane rubber rods with seven different hardnesses in the range of 60-90 HA on the forming quality of equal-diameter T-tube were analyzed. The research results show that with the gradual increasing of rubber hardness, the bulging height of branch tube increases, the wall thickness difference decreases, and wall thickness is more evenly distributed. When the rubber hardness is greater than 85 HA, the thinning rate at the top of branch tube is greater than 30%, and when the rubber hardness is less than 70 HA, the thickening rates at the end and bottom of straight tube are greater than 30%. Furthermore, when the rubber hardness is 85 HA in this study, the forming effect is the best with the maximum wall thickness of 1.899 mm, the minimum wall thickness of 1.06 mm and the bulging height for branch tube of 17.132 mm for the T-tube formed. In addition, the distribution law of the overall wall thickness for tube billet is that the top of branch tube is thinned and the end of straight tube is thickened, and the thickened area is obviously larger than the thinned area.

基金项目：

作者简介：张云峦（1979-），男，学士，工程师 E-mail：284713873@qq.com

参考文献：

[1] 陈名涛，肖小亭，刘易凡，等. 内压和加载路径对并列双支管内高压成形性的影响[J]. 塑性工程学报，2017, 24（5）：19-24.

Chen M T, Xiao X T, Liu Y F, et al. Effects of the internal pressure and loading path on hydroforming of the parallel arrangement multiway tube [J]. Journal of Plasticity Engineering, 2017, 24(5):19-24.

[2] 苑世剑，何祝斌，刘钢，等. 内高圧成形理论与技术的新进展[J]. 中国有色金属学报, 2011，21(10): 2523-2533.

Yuan S J, He Z B, Liu G, et al.New developments in theory and processes of internal high pressure forming[J].Chinese Journal of Nonferrous Metals，2011，21(10): 2523-2533.

[3] 杨兵，宋忠财，张卫刚，等. 管件液压成形的影响因素[J].上海交通大学学报，2005, 39(11): 1767-1770.

Yang B，Song Z C，Zhang W G, et al. The effect factors on the tube hydroforming process [J]. Journal of Shanghai Jiao Tong University, 2005，39(11): 1767-1770.

[4] Strano M, Altan T. An inverse energy approach to determine the flow stress of tubular materials for hydroforming applications [J]. Journal of Materials Processing Technology, 2004, 146（1）: 92-96.

[5] Nikhare C, Weiss P D. Buckling in low pressure tube hydroforming [J]. Journal of Manufacturing Processes, 2017, 1(28):1-10.

[6] 杜冰, 赵长财, 刘一江, 等. 管材内高压成形变形模式研究[J]. 机械工程学报, 2014, 50（16）:126-134.

Du B, Zhao C C, Liu Y J, et al. Research on different patterns of tube bulging process [J]. Journal of Mechanical Engineering, 2014, 50(16):126-134.

[7] 刘忠利，郭训忠，骆心怡，等. 汽车排气管件内高压成形数值模拟及试验[J]. 塑性工程学报，2015，22(4): 88-92.

Liu Z L，Guo X Z，Luo X Y，et al.Numerical simulation and experiment of the hydroforming for automobile exhaust pipe [J]. Journal of Plasticity Engineering, 2015，22(4): 88-92.

[8] 张彦敏，宋志真，孙爱学. 弹、塑性传力介质下三通管轴压胀形工艺分析[J]. 塑性工程学报，2008，2（15）:136-139.

Zhang Y M, Song Z Z, Sun A X. Analysis of axial force and internal pressure bulging process for tribranch tube with the elastic and plastic medium [J]. Journal of Plasticity Engineering, 2008, 2（15）: 136-139.

[9] 邹钱生，刘斌. 模具结构参数对橡胶介质胀形三通管的影响[J]. 华侨大学学报，2013, 34（2）:121-125.

Zou Q S，Liu B. Influence of mold structure parameters on Tshapes tubes by compound bulging using rubber medium [J]. Journal of Huaqiao University, 2013, 34（2）:121-125.

[10]Thiruvarudchelvan S. A novel hydraulicpressure augmented deepdrawing process for high draw ratios [J]. Journal of Materials Processing Technology, 1995,（54）: 355-361.

[11]Thiruvarudchelvan S. The potential role of flexible tools in metal forming [J]. Journal of Materials Processing Technology, 2002, （122）: 293-300.

[12]陈志忠, 刘斌. 采用橡胶介质的三通管胀形数值模拟[J]. 华侨大学学报，2011, 5（32）: 485-491.

Chen Z Z, Liu B. Simulation of bulge forming process for threeway tube using rubber medium[J]. Journal of Huaqiao University, 2011，5（32）：485-491.

服务与反馈：

【文章下载】【加入收藏】