锻压技术

基于数值模拟的车用法兰连接件多工位冷锻工艺研究与改进

英文标题：Research and improvement on multi-station cold forging process for vehicle flange connector based on numerical simulation

作者：卢蔚红

单位：梧州职业学院

关键词：法兰连接件冷锻工艺折叠缺陷网格流线成形载荷

分类号：TG316

出版年,卷(期):页码：2023,48(2):29-35

摘要：

以车用法兰连接件为研究对象，根据其结构特点，提出了一种6工位冷锻工艺方案，并采用Deform-3D对各工位成形过程进行了建模分析。结果显示，该方案能够获得外观填充完整的法兰连接件，但存在材料折叠缺陷。基于此，在原方案基础上提出了两种改进方案并依次进行了模拟，分析了改进后方案的网格流线变化图，同时对比了两种改进方案的成形载荷大小。结果表明：两种改进后方案均能够解决材料折叠问题，采用改进方案1时，成形载荷相对更小，更利于降低模具受载，提高模具寿命。经实际试模可知，按改进方案1生产的各工位零件与模拟结果一致，成形完整，无裂纹、折叠等缺陷，工艺可靠，该优化方法对多工位锻造技术的发展具有一定的推广作用。

For the vehicle flange connector, based on its structural characteristics, a six-station cold forging process scheme was proposed, and the forming process of each station was modeled and analyzed by Deform-3D. The results show that this scheme can obtain the flange connector with a completely filled appearance, but there are material folding defects. Thus, two improved schemes based on the original scheme were proposed and simulated in turn, and the grid streamline change diagrams of the improved schemes were analyzed. At the same time, the forming loads of the two improved schemes were compared. The results show that the two improved schemes can solve the problem of material folding. When the improved scheme 1 is adopted, the forming load is relatively smaller, which is more conducive to reducing the mold load and increasing the mold life. The actual mold test shows that the parts produced according to the improved scheme 1 are consistent with the simulation results, the forming is complete, there are no defects such as cracks and folds etc., and the process is reliable. Thus, this optimization method has a certain promotion effect on the development of multi-station forging technology.

基金项目：

2020年度广西高校中青年教师科研基础能力提升项目（2020KY49005）

作者简介：卢蔚红（1981-），女，学士，讲师，高级技师，E-mail：whlu81@163.com

参考文献：

[1]成美文, 刘风雷,李伟强,等.不锈钢高锁螺母多工位镦锻成形组织演变规律研究[J].热加工工艺,2020,49(5):103-107.

Cheng M W,Liu F L,Li W Q,et al.Study on microstructure evolution rule of multi-station upsetting for stainless steel high-lock nut[J].Hot Working Technology,2020,49(5):103-107.

[2]肖志玲, 刘百宣,孙红星,等.高强钢20MnTiB多工位冷镦变形行为[J].材料工程,2016,44(3):77-83.

Xiao Z L,Liu B X,Sun H X,et al.Multi-stage cold forging behavior of high strength steel 20MnTiB[J].Journal of Materials Engineering,2016,44(3):77-83.

[3]闫红艳, 郭永强,王志科,等.6寸法兰多工位闭式精锻工艺[J].锻压技术,2021,46(6):58-63，71.

Yan H Y,Guo Y Q,Wang Z K,et al.Multi-station closed precision forging process for six-inch flange[J].Forging & Stamping Technology,2021,46(6):58-63，71.

[4]陈凌翔, 李月超.汽车六角球头冷锻工艺优化与数值仿真[J].材料科学与工艺,2020,28(5):75-82.

Chen L X,Li Y C.Optimization and numerical simulation of cold forging process for automobile hexagonal ball head[J].Materials Science and Technology,2020,28(5):75-82.

[5]林雅杰, 仲太生,丁武学.车用齿轮毛坯多工位精密热模锻工艺分析及模具设计[J].锻压装备与制造技术,2019,54(3):82-87.

Lin Y J,Zhong T S,Ding W X.Process analysis and die design of multi-station precision hot die forging for automotive gear blank[J].China Metalforming Equipment & Manufacturing Technology,2019,54(3):82-87.

[6]李天翔, 张利虎.车用异形件浮动凹模冷镦工艺分析及模芯结构优化[J].锻压技术,2021,46(11):62-67，82.

Li T X,Zhang L H.Cold upsetting process analysis and die core structure optimization on floating die for special-shaped parts of vehicle[J].Forging & Stamping Technology,2021,46(11):62-67，82.

[7]梁强. 活塞销冷镦挤成形微折叠缺陷分析及改进措施[J].塑性工程学报,2018,25(6):99-104.

Liang Q.Micro-folding defect analysis and improvement of cold upsetting-extruding process for piston-pin[J].Journal of Plasticity Engineering,2018,25(6):99-104.

[8]张东民, 刘铭心,盛育东,等.薄壁六角螺母冷镦过程中模具磨损模拟分析及参数优化[J].润滑与密封,2017,42(10):114-117.

Zhang D M,Liu M X,Sheng Y D,et al.Process analysis and parameter optimization on die wear in cold heading for thin-walled hex nut[J].Lubrication Engineering,2017,42(10):114-117.

[9]赵志繁, 侯怀书,钱瑞福,等.六角法兰面锁紧螺母冷镦挤成型数值模拟及优化[J].热加工工艺,2020,49(17):101-104，107.

Zhao Z F,Hou H S,Qian R F,et al.Numerical simulation and optimization of cold heading-extrusion of hexagon flange face locking nuts[J].Hot Working Technology,2020,49(17):101-104，107.

[10]冯文杰, 杨创创,陈莹莹,等.基于数值模拟的汽车差速器齿轮冷挤压工艺方案[J].重庆理工大学学报：自然科学,2018,32(4):75-80.

Feng W J,Yang C C,Chen Y Y,et al.Study on cold extrusion process of automobile differential gears based on numerical simulation[J].Journal of Chongqing University of Technology：Natural Science,2018,32(4):75-80.

[11]胡建军, 李小平.Deform-3D塑性成形CAE教程[M].北京:北京大学出版社,2011.

Hu J J,Li X P.Deform-3D Plastic Forming CAE Application Tutorial[M].Beijing:Peking University Press,2011.

[12]董奇, 金飞翔,秦强,等.基于正交试验齿圈座热锻成形工艺优化[J].塑性工程学报,2021,28(8):18-22.

Dong Q，Jin F X,Qin Q,et al.Optimization of hot forging forming process based on orthogonal test for gear ring seat[J].Journal of Plasticity Engineering,2021,28(8):18-22.

服务与反馈：

【文章下载】【加入收藏】