Transactions of Materials and Heat Treatment

Title：Design of progressive stamping transfer die with multi-position for an automotive structural part

Authors： Liu Qingdong Xia Qinxiang

Unit： Guangzhou Institute of Technology South China University of Technology

KeyWords： automotive structural part progressive stamping transfer die progressive die AUTOFORM

ClassificationCode：TG386

year,vol(issue):pagenumber：2016,41(10):126-131

Abstract：

The structure of transfer die is different from that of progressive die, it is widely used in progressive stamping to produce large automotive structural part with a few steps. It consists of some independent dies whose numbers are equal to the number of steps. Independent dies have the similar features with small and medium die, and the die base has the similar features with the large stamping die. Therefore, the stamping feasibility of an automotive structural part was analyzed and the scheme was determined. The confirmed scheme was simulated by the software AUTOFORM to analyze stamping process, and a 6-steps progressive stamping transfer die was designed. The key technology of transfer die design for the automotive structural part was studied thoroughly. The production tests prove that the transfer die structure is reasonable, reliable and with high efficient. Thus, it is suitable for mass production of the automotive structural part.

Funds：

广东省品牌专业建设项目（粤教高函［2016］114号）

作者简介：刘庆东（1964-），男，硕士，高级工程师 E-mail：lqd64@hotmail.com

Reference：

[1]张正修. 多工位连续冲压技术及应用[M]. 北京：机械工业出版社，2010.

Zhang Z X. Multi-Position Progressive Stamping Technique and Application [M]. Beijing：China Machine Press，2010

[2]王孝培. 冲压手册[M]. 北京：机械工业出版社，2000.

Wang X P. Stamping Handbook [M]. Beijing：China Machine Press，2000.

[3]廖伟.汽车覆盖件模具设计技巧、经验及实例[M].北京：化学工业出版社，2013.

Liao W. The Skill，Experience and Case of Automobile Panel Die Design[M]．Beijing：Chemical Industry Press, 2013.

[4]周永新，刘红. 基于Dynaform的多次拉深工序优化设计[J]. 现代制造工程，2009, (9)：106-108.

Zhou Y X，Liu H．The multi-stage forming optimize based on Dynaform[J]. Modern Manufacturing Engineering，2009,(9):106-108.

[5]吴春明，阮锋，夏琴香，等. 基于有限元分析的级进模拉深工序优化设计[J].机床与液压，2006,34(2):29-31.

Wu C M，Ruan F，Xia Q X，et al.Optimum design of progressive die drawing sequence based on finite element analysis [J].Machine Tool ＆ Hydraulics，2006,34(2): 29-31.

[6]Seung Ho Kim，Se Ho Kim，Hoon Huh.Finite element inverse analysis for the design of intermediate dies in multistage deep-drawing processes with large aspect ratio [J].Journal of Materials Processing Technology，2001，113:779-785.

[7]陈炜，杨继昌，仲志刚，等.车身结构件多步冲压工艺数值模拟[J].汽车工程，2003，25(5): 518-521.

Chen W，Yang J C，Zhong Z G, et al.A simulation of multi-step sheet metal forming process for automotive body panel [J].Automotive Engineering，2003，25(5): 518-521.

[8]夏琴香，魏光明，叶福源，等. 多工位级进冲压全工序数值模拟关键技术研究[J].华南理工大学学报，2012，40(7): 62－66.

Xia Q X, Wei G M, Ye F Y, et al. The whole process numerical simulation research on key technologies of multi-position progressive stamping[J].Journal of South China University of Technology，2012，40(7): 62-66.

[9]钟江静，王迎春. 支承件多工位级进模具设计[J].锻压技术，2014,39(10):113-117.

Zhong J J, Wang Y C.Design on multi-position progressive die of the support[J].Forging & Stamping Technology，2014,39(10):113-117.

[10]Wei G M，Xia Q X, Zhang S J，et al.Layout design for high strength steel automotive structural parts based on UG-PDW[A]. 2011 Second International Conference on Mechanic Automation and Control Engineering[C]. China：Inner Mongolia，2011.

Service：

【This site has not yet opened Download Service】【Add Favorite】