Transactions of Materials and Heat Treatment

Title：Wear amount calculation and verification of 45 steel after induction quenching based on modified Archard model

Authors：

Unit：

KeyWords：

ClassificationCode：TH117.1；TH132.4

year,vol(issue):pagenumber：2020,45(10):203-208

Abstract：

In order to quantitatively analyze the influences of surface induction quenching heat treatment for 45 steel on surface wear, the yield strength of 45 steel when hardness was greater than 50 HRC obtained by the general steel module of software JMatPro. Then, the modified Archard wear calculation model was established by analyzing the actual working condition of reverse intermediate gear shaft for a certain type of transmission, and the yield strength corresponding to the 0.2 cm depth range of gear shaft outer cycle was taken as the strength calculated value in the modified Archard model. Furthermore, the wear amounts corresponding to the different yield strengths were obtained, and the actual wear amount of gear shaft was verified by the durable bench test. The results show that the error between the actual wear amount and the theoretical calculated value is 7.26%, which proves that the method of using the modified Archard model to calculate wear amount and taking the induction quenching surface hardness as the overall hardness is feasible and effective. Thus, the application of this method saves the cycle and test cost in new products development and has certain reference significance for the calculation and prediction of wear amount for similar material after surface hardening.

Funds：

国家自然科学基金资助项目(71361014)；江西省研究生创新专项资金项目（YC2019-S313）

钟流发（1983-），男，硕士研究生 E-mail：26517220@qq.com 通讯作者：刘祚时(1963-)，男，博士，教授 E-mail：liuzuoshi@163.com

Reference：

［1］温诗铸. 材料磨损研究的进展与思考
［J］.摩擦学学报,2008,28(1):1-4.

Wen S Z. Research progress on wear of materials
［J］. Tribology, 2008,28(1):1-4.

［2］Zapata D, Jaramillo J, Toro A. Rolling contact and adhesive wear of bainitic and pearlitic steels in low load regime
［J］.Wear, 2011,271(1/2):393-399.

［3］王晓笋, 巫世晶,陈杰,等.考虑动载荷与动态磨损系数的直齿轮传动系统动态磨损特性
［J］.中南大学学报：自然科学版,2014,45(2):408-413.

Wang X S, Wu S J, Chen J, et al. Dynamic surface wear characteristics in spur gear transmission system with dynamic loads and wear coefficients
［J］. Journal of Central South University: Science and Technology, 2014, 45(2):408-413.

［4］李万钟, 徐颖强,孙戬,等.滑动摩擦结合面磨合磨损表征方法与影响因素
［J］.中国表面工程,2017,30(1):125-131.

Li W Z, Xu Y Q, Sun J, et al. Characterization methods and influence factors of runningin wear between sliding joint surfaces
［J］. China Surface Engineering, 2017,30(1):125-131.

［5］胡波, 黄平.渐开线直齿圆柱齿轮磨损的数值计算与分析
［J］.润滑与密封,2017,42(12):23-28,33.

Hu B, Huang P. Numerical calculation and analysis of wear behavior of involute spur gear
［J］. Lubrication Engineering,2017,42(12):23-28,33.

［6］缪军, 龚红英,张杰,等.不同润滑介质作用下GCr15/10钢摩擦与润滑特性分析
［J］. 锻压技术,2018,43(7): 170-175.

Miao J, Gong H Y, Zhang J, et al. Analysis on friction and lubricating characteristics for steel GCr15/10 under different lubrication mediums
［J］. Forging & Stamping Technology, 2018, 43(7):170-175.

［7］张俊, 卞世元,鲁庆,等. 准静态工况下渐开线直齿轮齿面磨损建模与分析
［J］. 机械工程学报,2017,53(5):136-145.

Zhang J, Bian S Y, Lu Q, et al. Quasistatic model based wear analysis of spur gears
［J］. Journal of Mechanical Engineering,2017,53(5):136-145.

［8］宿月文, 陈渭,朱爱斌,等.滑动磨损过程有限元分析及销磨损预测
［J］.中国机械工程,2009,20(13):1573-1581.

Su Y W, Chen W, Zhu A B, et al. Simulation of sliding wear based on finite element method and its application to wear prediction of link pivot joint
［J］.China Mechanical Engineering,2009,20(13):1573-1581.

［9］谢仕芳, 张林伟,王武荣,等. 45钢与DC53钢的干滑动摩擦学行为
［J］.材料热处理学报, 2015, 36(6): 222-227.

Xie S F, Zhang L W, Wang W R, et al. Tribological behaviors of 45 steel against DC53 steel under dry sliding condition
［J］. Transactions of Materials and Heat Treatment, 2015,36(6):222-227.

［10］王爱琴, 谢敬佩,王文焱,等.表面感应淬火对45钢滚动磨损特性的影响
［J］.材料热处理学报,2007，(1): 127-129.

Wang A Q, Xie J P, Wang W Y, et al. Effect of induction hardening on rolling wear properties of 45 steel
［J］ .Transactions of Materials and Heat Treatment, 2007,(1):127-129.

［11］林信智, 齐松涛,赵文龙.感应淬火的频率选择
［J］.金属热处理,2015,40(3):209-211.

Lin X Z, Qi S T, Zhao W L. Choice of induction quenching frequency
［J］. Heat Treatment of Metals, 2015,40(3): 209-211.

［12］温诗铸, 黄平.摩擦学原理
［M］.第4版.北京:清华大学出版社,2012.

Wen S Z, Huang P. Principles of Tribology
［M］. The 4th Edition. Beijing: Tsinghua University Press,2012.

［13］Bartier O, Hernot X, Mauvoisin G. Theoretical and experimental analysis of contact radius for spherical indentation
［J］. Mechanics of Materials, 2010, 42(6):640-656.

［14］Kogut L, Jackson R L. A Comparison of contact modeling utilizing statistical and fractal approaches
［J］. Journal of Tribology, 2006, 128(1):213-217.

［15］GB/T 1172—1999, 黑色金属硬度及强度换算值
［S］.

GB/T 1172—1999, Convertion of haradness and strength for ferrous metal
［S］.

［16］韩德伟. 金属硬度检测技术手册
［M］.长沙:中南大学出版社,2007.

Han D W. Handbook for Technology of Hardness Determination of Metals
［M］. Changsha: Central South University Press, 2007.

［17］JeanPhilippe Schillé, Zhanli Guo, Nigel Saunders, et al. Modeling phase transformations and material properties critical to processing simulation of steels
［J］.Materials and Manufacturing Processes,2011, 26(1):137-143.

［18］桂长林. Archard的磨损设计计算模型及其应用方法
［J］.润滑与密封,1990,(1):12-21.

Gui C L. The Archard design calculation model and its application methods
［J］. Lubrication Engineering, 1990, (1):12-21.

Service：

【This site has not yet opened Download Service】【Add Favorite】