锻压技术

填充复合斜楔结构改进技术

英文标题：Improvement technology of filling compound wedge structure

作者：赵子海曹长才王健江克洪

分类号：

出版年,卷(期):页码：2022,47(3):178-181

摘要：

针对传统填充复合斜楔结构的缺点，提出了改进方法。传统填充复合斜楔结构中，采用刚性斜楔镶板来驱动活动驱动滑块和活动凸模，并且这二者均采用氮气缸进行回程,斜楔镶板由于高频次、高速运动和做功，导致磨损严重，影响斜楔结构的精度。对传统填充复合斜楔结构进行改进；采用气缸驱动活动驱动滑块和活动凸模进行工作和回程行程，有效地解决了传统填充斜楔结构使用时，由于斜楔镶板磨损引起的零件定位不可靠的问题。另外，采用辅助氮气缸推动活动凸模进行工作行程，也解决了气缸驱动活动凸模时冲压生产节拍慢的问题。

Aiming at the shortcomings of traditional filling compound wedge structure, the improvement methods were put forward. In the traditional filling compound wedge structure, the movable drive slider and movable punch were driven by the rigid wedge panel and returned by nitrogen cylinders, and because of high frequent and high-speed motion and work, the serious wear of wedge panel was caused which affected the accuracy of wedge structure. Therefore, the traditional filling compound wedge structure was improved, the working and return strokes were driven by the cylinder for movable drive slider and movable punch, which solved the problem of unreliable positioning for part caused by the wear of wedge panel when the traditional filling compound wedge structure was applied. In addition, the auxiliary nitrogen cylinder was used to carry out the working stroke of movable punch, which also solved the problem of slow stamping production rhythm when the cylinder drove the movable punch.

基金项目：

赵子海(1976-),男,本科，高级工程师 E-mail：714880894@qq.com

参考文献：

[1]赵子海, 缴平,廖小刚，等.特殊造型侧围外板加油口处冲压工艺分析[J].模具工业,2020,46(8):18-21，26.

Zhao Z H,Jiao P,Liao X G,et al.Research on stamping process of fuel filler area with special shape on body side outer panel[J]. Die & Mould Industry,2020,46(8):18-21，26.

[2]赵子海，孟宇轩，江克洪，等. 铝后门外板回弹补偿措施研究[J].模具工业,2020,46(11):37-40.

Zhao Z H,Meng Y X,Jiang K H,et al.Research on springback compensation of aluminum rear door outer panel[J]. Die & Mould Industry,2020,46(11):37-40.

[3]赵子海，王世锋，于海龙，等.后座椅靠背锁扣固定加强板冲压工艺研究[J].锻造与冲压，2020，483(10):48-51.

Zhao Z H,Wang S F,Yu H L,et al.Stamping process of a rear seat backrest lock catch stress plate[J].Forging & Metalforming,2020,483(10):48-51.

[4]赵子海，江克洪，王健，等.整体车门窗框处特殊包边机构原理研究[J].锻造与冲压，2021，501(4):55-58.

Zhao Z H,Jiang K H,Wang J,et al.Study on principle of special binding machanism at the window frame of an integral door[J].Forging & Metalforming,2021,501(4):55-58.

[5]赵子海，刘英堂，邵林江，等.侧围外板基准孔冲翻孔模结构改进[J].模具制造，2020，227(6):11-13.

Zhao Z H,Liu Y T,Shao L J,et al. Improvement of the die structure for the datumn hole burring of bodyside outer[J]. Die & Mould Manufacture,2020，227(6):11-13.

[6]赵子海，孟宇轩，刘英堂，等.汽车覆盖件铝板冲压工艺研究[J].模具制造，2020，223(2):29-32.

Zhao Z H,Meng Y X,Liu Y T,et al.Research on aluminium sheet parts stamping process for automobile[J]. Die & Mould Manufacture,2020，223(2):29-32.

[7]赵子海，凌世权，于海龙，等.侧围A柱处侧整形起皱问题对策探讨[J].锻造与冲压,2021,509(12):41-43.

Zhao Z H,Ling S Q, Yu H L, et al.Discussion on wrinkling during taking the side shaping of A-pillar and countermeasures taken[J].Forging & Metalforming,2021,591(12):41-43.

[8]赵子海，凌世权，李兴盛，等. 汽车覆盖件冲压模具降低噪声措施研究[J].锻造与冲压,2021,519(22):61-63.

Zhao Z H,Ling S Q, Li X S, et al. Research on noise reduction measures of automobile panel stamping die [J].Forging & Metalforming,2021,519(22):61-63.

[9]赵子海，张震宇，郝科伟，等.侧围外部C柱中部A面缺陷研究[J].模具制造，2020，233(12):29-31.

Zhao Z H,Zhang Z Y, Hao K W, et al.Research on A surface defect of bodyside outer at the C pillar area[J]. Die & Mould Manufacture,2020，233(12):29-31.

[10]赵子海，曹长才，谭植文，等.汽车覆盖件冲压模具热处理研究[J].模具制造，2019，221(12):81-84.

Zhao Z H,Cao C C, Tan Z W, et al. Research on heat treatment of stamping die for automobile panel[J]. Die & Mould Manufacture,2019，221(12):81-84.

[11]高双明，矫阿娇，崔礼春，等.某轿车后门内板冲压工艺及整形模具结构优化[J].锻压技术,2021,46(1):65-69.

Gao S M,Jiao A J, Cui L C, et al. Stamping process and structure optimization of sizing die for inner panel of a car rear door[J].Forging & Stamping Technology,2021,46(1）：65-69.

[12]孙鹏. 弹性夹片冲压工艺分析与模具设计[J].锻压技术,2020,45(12):160-164.

Sun P.Analysis of stamping process and die design for elastic clip[J].Forging & Stamping Technology,2020,45(12）：160-164.

服务与反馈：

【文章下载】【加入收藏】